Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Regenerative repair of rack-mount assemblages of a forward suspension bracket

Design of a rack the Poppy-fersona

1 — the Rack
2 — Пыльник an amortisation rod
3 — the Screw spring (it is compressed by means of the special tool)
4 — the Washer of the top saddle of a spring
5 — Assemblage of the top support of a rack
6 — the Washer of the top nut
7 — the Nut of fastening of the top support

Models Diamante, Galant (on 1993 and since 1999 of вып.) and Mirage

Dismantling

 PERFORMANCE ORDER

1. The design of rack-mount assemblage on the listed models is shown on an illustration.
2. Remove rack-mount assemblage from the car (see Has undressed Removal and installation of racks and screw springs of a forward suspension bracket).
3. By means of the special tool compress a screw spring.

4. Having pressed a rack to the top cover, compress it approximately on 1/2 courses of an amortisation rod, - at all up to the end!
5. Give the central nut and remove assemblage of the top support and the top saddle of a spring.

6. Remove a screw spring.


Assemblage

 PERFORMANCE ORDER

1. Establish on rack-mount assemblage the compressed screw spring.
2. Establish assemblage of the top support and tighten a nut of its fastening with demanded effort (59 H•м).
3. Release the tool compressing a spring.
4. Establish rack-mount assemblage on the car (see Has undressed Removal and installation of racks and screw springs of a forward suspension bracket).


Models Galant 1994 ÷ 1998 of вып.

Dismantling

 PERFORMANCE ORDER

1. Remove assemblage of the shock-absorber with a screw spring (see Has undressed Removal and installation of racks and screw springs of a forward suspension bracket).
2. Compress a spring by means of the special tool.
3. Release самоконтрящуюся a nut and remove the washer enclosed under it. Remove the plug, assemblage of the top support, and also a saddle of a spring with an overlay.


Installation

 PERFORMANCE ORDER

1. Establish on shock-absorber assemblage the screw spring compressed by means of the special tool, - track, that пруток springs has rested an end face against special sample in a saddle.
2. Establish пыльник, a rubber pillow, a cup, the top plug and a saddle with an overlay.
3. Tighten fixture, release a spring and establish assemblage on the car (see Has undressed Removal and installation of racks and screw springs of a forward suspension bracket).