Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal and installation of the cylinder of the lock of ignition

Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Onboard electric equipment see the Head). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation.


Removal

 PERFORMANCE ORDER

1. At a corresponding complete set of the car make deactivation of a pillow of safety (the Onboard electric equipment see the Head).
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Remove from the bottom finishing section the handle отпускания the cowl lock.
4. Remove a knee emphasis.
5. Remove an air sleeve of knee level and dismantle a steering wheel (see Has undressed Removal and steering wheel installation).
6. Remove the top and bottom sections of a casing of a steering column.
7. On models Diamante remove knee having blown and a sleeve of giving of air in a foot well.
8. In case of need liberate burn down electroconductings from intermediate clamps on a steering column.
9. Disunite corresponding contact sockets.
10. On models Galant and Diamante turn out fixing screws and remove on the left side of a steering column подрулевой the switch (in gathering with a contact spring of a pillow of safety - the models equipped SRS).
11. On models Diamante turn out fixing screws and take the switch of ignition of the cylinder замковой assemblages.
12. Insert a key into the cylinder of the lock of ignition and turn it in position АСС.
13. The suitable sharp tool push inside a lock pin in the cylinder of the lock of blocking of a steering column and take замковый the cylinder outside.
14. At a corresponding complete set dismantle the alarm gauge-switch of extraction of the ignition key.


Installation

 PERFORMANCE ORDER

1. On models Mirage establish the lock cylinder on the basic arm.

If arm replacement before обламыванием heads срезных locks make sure of serviceability of functioning of the cylinder was made.

2. On models Galant and Diamante establish the cylinder in a casing замковой assemblages, - track reliability защелкивания clamps. Fill in a casing the ignition switch, achieve combination замковых chinks and screw fixing screws.
3. On models Galant and Diamante establish into place assemblage подрулевого the switch with contact drum SRS, restore initial connection of electroconducting.
4. At a corresponding complete set establish the alarm gauge-switch of extraction of a key.
5. Connect electroconducting and establish a clamp.
6. If removed, establish into place knee having blown and an air line sleeve.
7. Establish casings of a steering column.
8. Establish a steering wheel and a knee emphasis.
9. Establish the handle отпускания the cowl lock.
10. Connect a negative wire to the battery, activate a pillow of safety and check up serviceability of functioning of the switch of ignition.