Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal of air from a hydraulic path of system of strengthening of a wheel

Forward steering drive

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props.
2. Some times manually turn a pulley of the steering pump.
3. Five-six times turn a steering wheel from an emphasis against the stop.
4. Disconnect ВВ a wire of system of ignition and, short jerks turning a starter, during 15 ÷ 20 seconds five-six times turn a steering wheel from an emphasis against the stop, - during prorolling watch, that the hydraulic liquid in the tank of the steering pump did not fall below level of an arrangement of the filter. If to spend prorolling at the working engine air present at a path will be adsorbed in a liquid, - make prorolling only by проворачивания not started engine.
5. Restore initial connection ВВ of a wire, start the engine and allow to it to work during some time for single turns.
6. Rotating a steering wheel, make sure of absence of occurrence of air bubbles in the pump tank.
7. Check up level and a condition of a hydraulic liquid, - it should not have a dairy-shaped consistence.
8. Make sure, that rotation of a steering wheel does not render appreciable influence on liquid level in the tank, - if the change size makes more than 5 mm, repeat prorolling procedure.


Back steering drive

 PERFORMANCE ORDER

1. Pump over a forward steering drive (see above).
2. Start the engine and leave its working on single turns.
3. Ослабьте the prorolling gate at the left on клапанной to management assemblage. Connect to the gate the special tool for prorolling of a hydraulic path (МВ991230).
4. Turn a steering wheel against the stop to the left, then at once return it in rectilinear position. Make sure of serviceability of an exit from a path of air bubbles.
5. Repeating the actions described in the previous paragraph, achieve full removal of air from a hydraulic contour, then muffle the engine.
6. Ослабьте on 1/8 turns the gate of prorolling of the strengthening cylinder of the back steering mechanism also connect to it the tool for prorolling, - the nozzle is equipped by the special emphasis limiting degree of opening of the gate.
7. Start the engine and make on the car a short trip with a speed about 80 km/h, having provided with that circulation of a hydraulic liquid in a path of a back steering drive.
8. Moving with a speed about 32 km/h, it is active повращайте a steering wheel, - air rests should leave from a path in reception capacity of a set for prorolling.
9. Continue procedure before full removal of air from system.