Mitsubishi Galant

1990-2001 of release

Repair and car operation

soap today

Suspension bracket and steering

The general information

The scheme of an arrangement of components of a forward suspension bracket on models Mirage on 1992 of вып. And models Diamante


1 — Шплинт 2 — the Power shaft 3 — the Washer 4 — the Support of the brake mechanism 5 — Самоконтрящаяся a nut 6 — the Finger of a spherical support of the bottom lever of a suspension bracket	7 — Шплинт 8 — Шаровый a finger of a tip of steering draught 9 — the Power shaft 10 — the Bolt of the bottom support of a rack 11 — Assemblage of a nave with a rotary fist

Design of a back suspension bracket of models Mirage on 1992 вып.


9 — Болтовая pair of fastening of a cross-section jet bar 10 — the Protective cover 11 — the Top nut of fastening of the shock-absorber (2 шт)	12 — the Bolt of fastening of the longitudinal lever of a suspension bracket 13 — the Beam of the back bridge

The scheme of an arrangement of components of a forward suspension bracket on models Mirage since 1993 вып.


1 — the Tip of steering draught 2 — the Bottom spherical support 3 — the Bottom operating lever 4 — the Support of the bottom operating lever 5 — the Bar of the stabilizer of cross-section stability	6 — the Rack of the stabilizer of cross-section stability 7 — a suspension bracket Rack 8 — Assemblage of a nave with the wheel bearing 9 — the Power shaft

The scheme of an arrangement of components of a forward suspension bracket on models Galant 1994 ч 1998 of вып.


1 — a suspension bracket Rack 2 — the Rotary fist 3 — Assemblage of a nave with the wheel bearing 4 — the Bottom spherical support 5 — Jet section of the bottom operating lever 6 — Cross-section section of the bottom operating lever	7 — Support of sections of the bottom operating lever 8 — Реечная transfer of a steering drive 9 — the Bar of the stabilizer of cross-section stability 10 — the Power shaft 11 — the Top spherical support 12 — the Top operating lever

The scheme of an arrangement of components of a forward suspension bracket on models Galant since 1999 of вып.


1 — the Tip of steering draught 2 — the Bottom spherical support 3 — the Bottom operating lever 4 — the Support of the bottom operating lever	5 — the Bar of the stabilizer of cross-section stability 6 — a suspension bracket Rack 7 — Assemblage of a nave with the wheel bearing 8 — the Power shaft

Design of a back suspension bracket of models Mirage since 1993 вып.


1 — Ступичная assemblage 2 — the Bottom operating lever 3 — Operating draught	4 — the Longitudinal lever of a suspension bracket 5 — Rack-mount assemblage

Design of a back suspension bracket of models Galant on 1993 вып.


11 — Болтовая pair of fastening of a cross-section jet bar 12 — the Protective cover 13 — the Top nut of fastening of the shock-absorber (2 шт)	14 — the Bolt of fastening of the longitudinal lever of a suspension bracket 15 — the Beam of the back bridge

Design of a back suspension bracket of models Galant 1994 ч 1998 of вып.


1 — the Longitudinal lever of a suspension bracket 2 — the Bottom operating lever 3 — the Operating lever of adjustment of disorder	4 — the Rack 5 — Ступичная assemblage

Design of a back suspension bracket of models Diamante 1992 ч 1996 of вып. Without 4WS


1 — the Top nuts of fastening of the shock-absorber 2 — the Bolt 3 — Bolts of fastening of a brake support 4 — Assemblage of a brake support 5 — the Brake disk	6 — the Bolt 7 — the Tip of a cable of a drive of a lay brake 8 — Болтовая pair of fastening of the longitudinal lever of a suspension bracket 9 — Bolts of fastening of a beam 10 — the Beam of the back bridge

Design of a back suspension bracket of models Galant c 1999 вып.


1 — the Longitudinal lever of a suspension bracket 2 — Ступичная assemblage 3 — the Bottom operating lever of a suspension bracket 4 — Rack-mount assemblage	5 — the Stabilizer of cross-section stability 6 — a stabilizer Rack 7 — the Rotary fist 8 — the Operating lever of adjustment of disorder

Design of a back suspension bracket of models Diamante 1992 ч 1996 of вып. With 4WS


1 — the Top nuts of fastening of the shock-absorber 2 — the Bolt 3 — Bolts of fastening of a brake support 4 — Assemblage of a brake support 5 — the Brake disk 6 — the Bolt 7 — the Tip of a cable of a drive of a lay brake	8 — the Bolt (models with ABS) 9 — Штуцерный a socket 10 — the Nut of a tip of steering draught 11 — Штуцерные sockets of hydraulic tubes of a steering drive 12 — Болтовая pair of fastening of the longitudinal lever of a suspension bracket 13 — the Nut of fastening of a beam 14 — the Beam of the back bridge

Design of a back suspension bracket of models Diamante since 1997 вып.

As procedures of service of components of a suspension bracket are carried out under the car, it is necessary to take care in advance of possibilities of lifting of a vehicle and its fixing in the lifted position (prepare reliable a jack and props).

At all do not perform any works under the car, fixed in the lifted position only by means of a jack!

Forward suspension bracket

The forward suspension bracket on all models has an independent design. Rotary fists are connected to operating levers of a suspension bracket by means of spherical support. The opposite ends levers приболчены to a frame. The stabilizer of cross-section stability reducing rocking and a list of the car on turns enters into a regular complete set.

Basis of a forward suspension bracket on the majority of models the racks make the Poppy-fersona consisting of telescopic shock-absorbers and screw springs. On models Galant 1994 ч 1998 of вып. Separately established telescopic shock-absorbers about screw springs are used.

Back suspension bracket

The design of a back suspension bracket of models considered in the present Management is organised by means of rack-mount assemblages / telescopic shock-absorbers with screw springs and operating levers/draughts and presented on illustrations.

Steering drive

All models are equipped by the hydrostrengthened steering transfer реечного the type, connected to rotary fists by means of two steering draughts. Carter of the steering mechanism приболчен to the back party of a longitudinal beam.

The steering drive is organised by means of two cross-section draughts, spherical which fingers of tips are mounted on rotary fists of operated wheels of the car.

Often in the course of service of components of a suspension bracket and a steering drive it is necessary to face with resistant отдаванию fixture. “ Прикипание ”fixture elements it is connected by that they are constantly subject to external influences, are in contact to water, a dirt, a soot and other promoting development of corrosion by substances. For the purpose of simplification of procedure отдавания its such"become attached"fixture it is necessary to impregnate with plentiful quantity of getting oil beforehand. Зачистка open carving parts of fixture a rigid wire brush also promotes simplification отдавания приржавевших nuts. Sometimes, in especially heavy cases, for отпускания the"become attached"bolt/nut it is possible to take advantage выколоткой. Выколотка rests against edge шлица bolt nuts/heads, then sharp blows by a hammer are struck to its opposite end. Watch that выколотка has broken, try to damage inexact blows a carving. Effective enough way is also warming up resistant отдаванию fixture and a surface of a component surrounding it a torch of a blowtorch or a gas torch though composers of the given Management and do not recommend to resort without extreme need to such technology in view of its potential danger connected with possibility of ignition and risk of reception of burns. Extension pieces, collars and trumpet nozzles are intended for increase in the twisting moment at отпускании fixture on them of a various sort. However, remember, that it is not necessary to use such intensifying adaptations complete with the drive equipped with "rattle" - the risk of failure of the ratchet mechanism is too great. Sometimes the "become attached" fixture starts to give in after preliminary slightly will be tightened clockwise. All fixture, отпускание which has demanded application of not ordinary measures at assemblage is subject to replacement!

After отдавания attentively check a condition of fixture and in case of need make its replacement with elements of the same standard size. At assemblage tighten elements of fixture of components of a suspension bracket and a steering it is strict with demanded effort.

At all do not undertake attempts рихтовки the deformed components of a suspension bracket and a steering - replace defective details new!