Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal and steering wheel installation

Models Mirage on 1993 вып.

Removal

 PERFORMANCE ORDER

1. Result forward wheels of the car in rectilinear position. Disconnect from the battery a negative wire.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Remove with ступичной parts of a steering wheel an overlay of the button of activation of a horn, - delay an overlay bottom edge upwards, then disconnect electroconducting.
3. Give a nut of fastening of a steering wheel.
4. Mark position of a wheel concerning a steering shaft.
5. By means of a special stripper remove a wheel from a steering column.

At all do not make attempts to bring down a wheel from a shaft by means of a hammer!


Installation

 PERFORMANCE ORDER

1. Watching correctness of combination of the adjusting labels put in the course of dismantle, plant a wheel on a shaft of a steering column.
2. Screw a fixing nut and tighten it with demanded effort (40 H•м).
3. Connect electroconducting and establish on ступичную a part of a steering wheel an overlay of activation of a horn.
4. Connect a negative wire to the battery.


Models Galant on 1993 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Remove an overlay of activation of a horn: on models on 1991 вып. The overlay should be wrung out upwards for the purpose of its liberation from clamps, to lift and disconnect electroconducting; on models 1992 ÷ of 1993 of вып. Preliminary to turn out located in the bottom part of an overlay the screw.
3. Give a fixing nut.
4. Mark position of a wheel concerning a steering shaft.
5. By means of a special stripper remove a wheel from a steering column.

At all do not make attempts to bring down a wheel from a shaft by means of a hammer!


Installation

 PERFORMANCE ORDER

1. Watching correctness of combination of the adjusting labels put in the course of dismantle, plant a wheel on a shaft of a steering column.
2. Screw a fixing nut and tighten it with demanded effort (35 ÷ 45 H•м).
3. Connect electroconducting and establish on ступичную a part of a steering wheel an overlay of activation of a horn.
4. Connect a negative wire to the battery.


Models Galant and Mirage since 1994 вып.

Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Onboard electric equipment see the Head). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation. In order to avoid system SRS damage, track, that the steering shaft was not turned after steering wheel removal. Block a column the ignition key at rectilinear position of forward wheels.


Removal

 PERFORMANCE ORDER

1. Result forward wheels of the car in rectilinear position.
2. Make deactivation SRS (the Onboard electric equipment see the Head).

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Having hooked, remove lateral plastic covers and give located under assemblage of a steering wheel screws of fastening of the module of a pillow of safety.

4. For a detachment of a socket of a spring contact drum of a pillow of safety release a clamp, having wrung out it towards the module. Keeping a clamp wrung out, accurately hook a socket the suitable tool and disconnect it from the module.

5. Remove the module of a pillow of safety and lay its cover upwards transfer it on a pure dry surface.

6. Mark position of a steering wheel concerning a column shaft.
7. Give a fixing nut and remove a wheel, having taken advantage of a suitable stripper, - at all do not make attempts to bring down a wheel from a shaft by means of a hammer!

In order to avoid infringement of centering of contact cable drum SRS do not suppose проворачивания a steering shaft at the removed steering wheel. At the compelled infringement of the given requirement the drum should be centered before wheel installation into place.



Installation

 PERFORMANCE ORDER

1. Make sure, that forward wheels of the car remain in rectilinear position. In case of need make centering of a spring contact drum of a pillow of safety, - achieve combination of label NEUTRAL with the reciprocal index on a casing.
2. Plant a steering wheel on a column shaft, - track correctness of combination of the labels put in the course of dismantle. Screw a fixing nut and tighten it with demanded effort (40 H•м).
3. Establish the module of a pillow of safety.
4. Connect a negative wire to the battery, turn the ignition key in position ON, - on the panel of devices control lamp SRS should join for seven seconds.


Models Diamante

Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Onboard electric equipment see the Head). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation. In order to avoid system SRS damage, track, that the steering shaft was not turned after steering wheel removal. Block a column the ignition key at rectilinear position of forward wheels.


Removal

 PERFORMANCE ORDER

1. Result forward wheels of the car in rectilinear position.
2. Make deactivation SRS (the Onboard electric equipment see the Head).

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Give located under assemblage of a steering wheel of a nut of fastening of the module of a pillow of safety.
4. For a detachment of a socket of a spring contact drum of a pillow of safety release a clamp, having wrung out it towards the module. Keeping a clamp wrung out, accurately hook a socket the suitable tool and disconnect it from the module.
5. Remove the module of a pillow of safety and lay its cover upwards transfer it on a pure dry surface.
6. Mark position of a steering wheel concerning a column shaft.
7. Give a fixing nut and remove a wheel, having taken advantage of a suitable stripper, - at all do not make attempts to bring down a wheel from a shaft by means of a hammer!

In order to avoid infringement of centering contact обельного drum SRS do not suppose проворачивания a steering shaft at the removed steering wheel. At the compelled infringement of the given requirement the drum should be centered before wheel installation into place.


Installation

 PERFORMANCE ORDER

1. Make sure, that forward wheels of the car remain in rectilinear position. In case of need make centering of a spring contact drum of a pillow of safety, - achieve combination of label NEUTRAL with the reciprocal index on a casing.
2. Plant a steering wheel on a column shaft, - track correctness of combination of the labels put in the course of dismantle. Screw a fixing nut and tighten it with demanded effort (40 H•м: for models 1992 ÷ of 1993 of вып. And 45 H•м: for models since 1994 вып.).
3. Establish the module of a pillow of safety and tighten nuts of its fastening with demanded effort (5 H•м).
4. Connect a negative wire to the battery, turn the ignition key in position ON, - on the panel of devices control lamp SRS should join for seven seconds.