Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Regenerative repair of rack-mount assemblages of a back suspension bracket

Design of rack-mount assemblage of a back suspension bracket of models Mirage and Galant since 1994 вып.

1 — the Protective cover
2 — Самоконтрящаяся a nut
3 — the Washer
4 — the Top plug And
5 — the Top saddle of a spring
6 — the Overlay of a saddle of a spring
7 — the Top plug In

8 — the Metal plug
9 — the Cup
10 — Пыльник
11 — the Terminator of a course of compression
12 — the Screw spring
13 — the Shock-absorber
N — Replace


Models Mirage and Galant since 1994 вып.

Dismantling

 PERFORMANCE ORDER

1. The design of rack-mount assemblage of a back suspension bracket of models Galant and Mirage is shown on an illustration.
2. Remove rack-mount assemblage from the car (see Has undressed Removal and installation of back racks).
3. The special tool compress a screw spring.
4. Remove a protective cover.
5. Keeping a rod of the shock-absorber from проворачивания, give самоконтрящуюся a nut.
6. Remove assemblage of the top saddle of a spring with an overlay.
7. Remove the metal plug, plugs And and In, a cup, the terminator of a course of compression and a dustproof casing.
8. Remove from the shock-absorber the compressed screw spring.


Installation

 PERFORMANCE ORDER

1. Establish the compressed screw spring on the shock-absorber, - achieve end face hit прутка an extreme coil of a spring in deepening in a saddle overlay.
2. Establish on the shock-absorber пыльник, the terminator of a course of compression, a cup, metal and rubber plugs, a saddle of a spring with an overlay.
3. Put on a shock-absorber rod the top plug And and a washer.
4. Screw new самоконтрящуюся a nut and temporarily it tighten.
5. Remove the tool compressing a spring, then tighten definitively самоконтрящуюся a nut with demanded effort (25 H•м).
6. Establish a protective cover.
7. Establish assemblage of the shock-absorber with a screw spring on the regular place on the car (see Has undressed Removal and installation of back racks).