Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal and installation of the back stabilizer of cross-section stability

Models Galant on 1993 вып.

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props.
2. Prop up a jack a beam of the back bridge.
3. Give самоконтрящиеся fixing nuts and remove basic arms of the bottom beam.
4. Turn out fixing bolts and remove assembly collars of a bar of the stabilizer of cross-section stability.
5. Keeping a bar of the stabilizer from проворачивания a wrench, give самоконтрящуюся a nut.
6. Remove basic cups and the rubber plug.
7. A wrench block a rack of the stabilizer from проворачивания and release самоконтрящуюся a nut of its fastening. Operating in a similar manner, disconnect the second rack.
8. Lower a jack which is propping up a beam of the back bridge, having left a small backlash between a suspension bracket and a car body.
9. Take a bar of the stabilizer of cross-section stability from under the car.
10. Check up a condition of a bar of the stabilizer and estimate degree of deterioration of components of its fastening.


Installation

 PERFORMANCE ORDER

1. Get a bar of the stabilizer of cross-section stability on the regular place and raise a jack a beam of the back bridge.
2. Connect to a bar of a rack of the stabilizer and fix their new самоконтрящимися nuts, having tightened the last with effort 45 H•м.
3. Establish the central plugs and collars of fastening of the stabilizer. Screw fixing bolts and tighten them with demanded effort (14 H•м).
4. Return into place a cable of a drive of a lay brake, tighten an adjusting bolt of the wheel gauge.
5. Establish a basic arm of the bottom beam, tighten a fixing bolt with effort 85 H•м, a nut - 130 H•м.
6. Establish in beam arms new rubber pillows, tighten new самоконтрящиеся nuts with demanded effort (110 ÷ 130 H•м).
7. Lower the car on the earth.


Models Diamante and Galant 1994 ÷ 1998 of вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.

3. Give самоконтрящиеся nuts of fastening of racks of the stabilizer of cross-section stability.

4. Turn out bolts of fastening of assembly collars, remove rubber plugs.
5. Remove a bar of the stabilizer from the car.
6. Check up a condition of a bar of the stabilizer and estimate degree of deterioration of components of its fastening.


Installation

 PERFORMANCE ORDER

1. Get a stabilizer bar on the regular place.
2. Freely fix assembly collars.
3. Achieve correct combination of adjusting marks, - the labels put on a bar should appear on distance about 10 mm from external edges of both assembly collars.
4. Having levelled a bar in the demanded image, tighten fixing nuts with demanded effort (38 H•м).
5. Connect stabilizer racks to демпферным to plugs and a bar. Tighten fixing nuts with demanded effort (38 H•м).
6. Lower the car on the earth.
7. Connect a negative wire to the battery.