Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Adjustment of wheel bearings

Models Mirage

Replacement of wheel bearings is made in gathering with naves!


 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
2. Remove a support and a disk of the brake mechanism / a brake drum (the Brake system see the Head).
3. Remove a dustproof cover and tighten фланцевую a nut with effort 180 H•м.
4. With the help циферблатного a measuring instrument плунжерного type define size axial люфта the wheel bearing/stupichnoj of assemblage. The maximum admissible value makes 0.05 mm.
5. By means of a dynamometer and a cord wound round heads of bolts measure effort проворачивания the assemblage bearing/stupichnoj, - the maximum admissible value makes 19 Н.
6. If results any of checks fall outside the limits an admissible range, replace a nave.
7. Establish into place a dustproof cover.
8. Establish a brake disk with a support / a brake drum.
9. Establish a wheel and lower the car on the earth.


Models Galant on 1993 вып.

On the models equipped with disk brake mechanisms of back wheels the naves of tight execution which are not requiring adjustment are established. It is more low resulted the description of procedure of adjustment of wheel bearings for models with drum-type back brake mechanisms.


 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
2. Remove a dustproof cover and give ступичную a nut.
3. Rotating a nave / a brake drum, tighten a nut of the wheel bearing with effort 27 H•м.
4. Release an adjusting nut for removal of a pretightness of the bearing, then tighten it again with effort 10 H•м.
5. Block a nut and establish new шплинт.
6. Establish into place a wheel and lower the car on the earth.


Models Diamante and Galant since 1994 вып.

 PERFORMANCE ORDER

With the help циферблатного a measuring instrument плунжерного type define size axial люфта the wheel bearing/nave. The maximum admissible value makes 0.05 mm at the counternut tightened with demanded effort. Adjustment of bearings on the given models is not represented possible, - defective components are subject to replacement.