Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal and installation of draughts of a steering drive

Tips of steering draughts

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props. Remove a corresponding forward wheel.
3. Take шплинт and give корончатую a nut of fastening of an external tip of steering draught on assemblage of a rotary fist, - шплинты are subject to replacement without fail.

4. By means of a special stripper separate a tip from a rotary fist.

5. Mark position of a counternut concerning a tip.

6. One key keeping a tip from проворачивания, the second release its counternut, - it is necessary to give a nut on one full turn, no more!

7. Rotating a tip, remove it from a draught bar.


Installation

 PERFORMANCE ORDER

1. Smooth out a carving on a draught bar (a steering drive of forward wheels).
2. Screw a tip on a bar against the stop in a counternut, then turn away it on one full turn back and tighten a nut before combination of the adjusting labels put in the course of dismantle.
3. Fill шаровый a tip finger in a landing nest in assemblage of a rotary fist, make sure, that wheels are established in rectilinear position, screw корончатую a nut and tighten it with demanded effort (34 H•м: models Mirage and 29 H•м: models Galant and Diamante). By pulling up (not отпускания) a nut achieve combination of apertures under installation шплинта. Establish new шплинт, reliably having dissolved its short moustaches.
4. Establish into place a wheel. Lower the car on the earth and tighten wheel nuts with demanded effort (90 ÷ 110 H•м).
5. Connect a negative wire to the battery
6. Tighten a counternut of a tip with demanded effort (42 H•м: models Mirage and 49 ÷ 53 H•м: models Galant and Diamante).
7. Check up corners of installation of forward wheels, in case of need make corresponding updating.


Bars of steering draughts

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props.
2. Remove a corresponding forward wheel.
3. Take шплинт and give корончатую a nut of a spherical finger of an external tip of steering draught.
4. A wire brush smooth out a carving of a bar of steering draught and moisten with its getting oil.
5. By means of a stripper liberate a tip from a rotary fist.
6. Ослабьте a counternut also remove from a bar an external tip, - count quantity of turns on which the tip was will screw.
7. Release a counternut of fastening of bent for реечной to transfer.
8. Release fixing collars and remove the goffered protective cover картера the steering mechanism.
9. Unbend uvulas of a lock plate ослабьте a fixing nut and disconnect the internal end of a bar from assemblage реечной transfers.


Installation

 PERFORMANCE ORDER

1. Having replaced a lock plate, establish draught and tighten it with demanded effort (90 H•м).
2. Bend uvulas of a lock plate.
3. Establish into place a protective cover and fix its new collars.
4. Establish an external tip of steering draught (the previous subsection see), - track, that the tip was will screw precisely for the quantity of turns fixed in the course of dismantle.
5. Fix a tip in a rotary fist, screw and tighten with demanded effort корончатую a nut of a spherical finger.
6. Establish a wheel and lower the car on the earth.
7. Check up corners of installation of forward wheels, in case of need make corresponding updating.