Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


арахис сырой опт


Removal and installation of the steering mechanism from a manual drive

Details of installation of the steering mechanism with a manual drive (model Mirage)

1 — the Bolt of fastening of a shaft of a steering column to an axis приводной gear wheels реечной transfers
2 — the Collar
3 — Шплинт
4 — Шаровый a finger of a tip of steering draught
5 — the Assembly collar

6 — the Assembly collar
7 — Carter of the steering mechanism
8 — the Cover
N — Replace


Some from considered in the present Management of model of cars are equipped by system of additional safety (SRS). Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Onboard electric equipment see the Head). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation.


Models Mirage

Removal

 PERFORMANCE ORDER

1. Details of installation of the steering mechanism on models Mirage are shown on an accompanying illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Поддомкратьте the car also establish it on props. Remove forward wheels.
4. Disconnect electroconducting from the oxygen gauge and remove a reception pipe of system of release of the fulfilled gases.
5. Prop up/hang out the power unit. Give bolts of fastening of both jet emphasis of a suspension bracket of the unit.
6. Turn out four fixing bolts and remove the central beam.
7. Release a coupling bolt of fastening bottom карданного the hinge of a steering column to an entrance shaft реечной transfers, - preliminary mark adjusting position of components.
8. Take шплинты, give корончатые nuts and liberate tips of steering draughts from rotary fists.
9. Release fixing bolts of assembly collars and take assemblage of the steering mechanism with rubber pillows of its support through an arch of the right wheel.


Installation

 PERFORMANCE ORDER

1. Get assemblage of the steering mechanism on the regular place, - track correctness of combination of the landing labels of shaft put in the course of dismantle.
2. Establish assembly collars and tighten bolts of their fastening with demanded effort (70 H•м).
3. Tighten with demanded effort (18 H•м) a coupling bolt of fastening of the bottom shaft of a column to an entrance shaft реечной transfers.
4. Establish the central beam.
5. Establish a reception pipe of system of release of the fulfilled gases.
6. Connect electroconducting to the oxygen gauge.
7. Connect tips of steering bent for to rotary fists, tighten with demanded effort корончатые nuts and fix their new шплинтами.
8. Check up corners of installation of forward wheels, in case of need make corresponding updating.