Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal and installation of wheel hairpins

Naves of the wheels equipped with disk brake mechanisms

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props. Remove a corresponding wheel.
2. Remove a support and колодки the brake mechanism (the Brake system see the Head). Tie up a support a wire to suspension bracket elements, - track, that the brake hose has not appeared tense.
3. Remove ступичную assemblage (see Has undressed Removal and installation ступичных assemblages).

4. Transfer assemblage on a workbench and establish on a suitable emphasis. By means of a press squeeze out of a disk wheel hairpins.

If possibility of use of a press is absent, hairpins can be beaten accurately out by means of stupid brass выколотки, - track uniformity of an emphasis of a disk.


Installation

 PERFORMANCE ORDER

1. A rigid brush clean apertures under installation of hairpins in ступичной to assemblage.
2. By means of a hammer fill a hairpin in a reception aperture, - do not use any greasings and hermetics.

3. Definitive planting of hairpins is carried out by means of a press.

In the absence of possibility to take advantage of a press, pass a hairpin in a reception nest, then put on it about four flat washers and screw a wheel nut. Keeping ступичную assemblage start to tighten a nut, - the hairpin should come into a nest. Make sure of completeness of planting of a hairpin, then remove a nut and washers.

4. Establish ступичную assemblage and adjust wheel bearings (the Section Adjustment of wheel bearings see).
5. Establish колодки and a support of the brake mechanism.
6. Establish a wheel and lower the car on the earth. Tighten wheel nuts with demanded effort.


Naves of the wheels equipped with drum-type brake mechanisms

Removal

 PERFORMANCE ORDER

1. Details of installation of wheel hairpins are shown on an illustration.

2. Поддомкратьте the car also establish it on props. Remove a corresponding wheel.
3. Remove a brake drum (the Brake system see the Head).
4. In case of need remove brake boots (the Brake system see the Head).

5. By means of the big clamp and a suitable face head squeeze out a hairpin of an axis flange.


Installation

 PERFORMANCE ORDER

1. Grease the surface of a hairpin equipped with a notch with liquid soap and pass it in a reception aperture

2. Put on a hairpin of an order of four flat washers and screw a wheel nut. Keeping a flange from проворачивания, start to tighten a nut, - the hairpin should come into a nest. Make sure of completeness of planting of a hairpin, then remove a nut and washers.

4. If removed, establish into place brake boots (the Brake system see the Head).
5. Establish a brake drum (the Brake system see the Head).
6. Establish a wheel and lower the car on the earth.
7. Tighten wheel nuts with demanded effort.