Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
- The engine
   - Removal/installation of the power unit, dismantle of components
      The general information
      Removal and engine installation
      Removal and installation of a cover of a head of cylinders
      Removal and installation of assemblages of a drive of valves
      Removal and thermostat installation
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and installation турбокомпрессора
      Removal and installation of a radiator of system of cooling (all models)
      Removal and installation of the fan of system of cooling of the engine
      Removal and installation of the water pump
      Removal and installation of a head of cylinders
      Removal and pallet installation картера the engine
      Removal and installation of the oil pump
      Removal and installation демпфера крутильных fluctuations of a cranked shaft
      Removal and installation of a cover of drive ГРМ and газораспределительного a belt
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of a drive of valves, check of a condition of components
      Removal and installation of a balancing shaft
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of a flywheel/privodnogo of a disk
   + Regenerative repair of the engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and thermostat installation

In order to avoid reception of burns, start performance of works only after definitive cooling of system! Do not suppose antifreeze hit on open sites of a body and the painted surfaces of the car. Casually got splashes immediately wash off plentiful quantity of water. Remember that antifreeze is extremely a toxic liquid and its hit in an organism even in small amounts is fraught with the most serious consequences (up to a lethal outcome). Never leave antifreeze stored in leaky closed container and immediately collect cooling liquid spilt on a floor. Remember that the sweetish smell of antifreeze can draw to itself attention of children and animals. About ways recyclings of the fulfilled cooling liquid consult at any station of car-care centre. In many regions of the world special points on reception of a various sort of working off are equipped. At all do not merge an old cooling liquid in the water drain and on the earth!


Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Empty cooling system (see the Head of Adjustment and routine maintenance).
3. Remove all components limiting access to the thermostat.
4. Turn out fixing bolts and remove a casing of the thermostat from the engine.

5. Take from a casing the thermostat, - try to remember correct adjusting position of assemblage. The sealing ring of the thermostat is subject to replacement without fail!


Installation

 PERFORMANCE ORDER

1. Fill the thermostat in a casing, - track density of planting of a flange in a flute chosen in a body of the inlet pipeline or a casing. Achieve correct combination спускного the valve with a label on a thermostat casing.
2. Having replaced a sealing ring, establish a thermostat casing on the regular place and tighten bolts of its fastening with demanded effort (Specifications see).
3. Fill in in cooling system necessary quantity of a mix of a demanded grade (see the Head of Adjustment and routine maintenance).
4. Establish components acting in film for the purpose of providing of access.
5. Connect a negative wire to the battery. Start the engine and warm up it to normal working temperature (the thermostat should open) and add in a radiator a little more a cooling liquid, having finished its level to the bottom cut of a mouth.
6. After engine cooling once again check up level of a cooling liquid, in case of need make corresponding updating.