Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
- The engine
   - Removal/installation of the power unit, dismantle of components
      The general information
      Removal and engine installation
      Removal and installation of a cover of a head of cylinders
      Removal and installation of assemblages of a drive of valves
      Removal and thermostat installation
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and installation турбокомпрессора
      Removal and installation of a radiator of system of cooling (all models)
      Removal and installation of the fan of system of cooling of the engine
      Removal and installation of the water pump
      Removal and installation of a head of cylinders
      Removal and pallet installation картера the engine
      Removal and installation of the oil pump
      Removal and installation демпфера крутильных fluctuations of a cranked shaft
      Removal and installation of a cover of drive ГРМ and газораспределительного a belt
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of a drive of valves, check of a condition of components
      Removal and installation of a balancing shaft
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of a flywheel/privodnogo of a disk
   + Regenerative repair of the engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Replacement of a back epiploon of a cranked shaft

Details of installation of a back epiploon of a cranked shaft (all models)

1 — Адаптерная a plate
2 — the Landing plate
3 — the Back plate
4 — an epiploon Casing
5 — the Epiploon
6 — Bolts of fastening of a cover of bearings
7 — the Cover of bearings
8 — the Persistent bearing And

9 — the Persistent bearing
10 — the Bottom loose leaf of the radical bearing
11 — the Cranked shaft
12 — the Persistent bearing In
13 — the Persistent bearing And
14 — the Top loose leaf of the radical bearing
15 — the Block of cylinders


Removal

 PERFORMANCE ORDER

1. Details of installation of a back epiploon of a cranked shaft are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Remove transmission.
4. Remove assemblage of a flywheel/privodnogo of a disk (see Has undressed Removal and installation of a flywheel/privodnogo of a disk).
5. Remove a back plate and a transmission dome.
6. If leaks through a casing of a back epiploon take place, remove a casing. If the casing is perfectly in order, simply take from it an epiploon.

On some engines the separator which also is subject to removal is in addition established.


Installation

 PERFORMANCE ORDER

1. Grease internal sponges of a new epiploon with pure impellent oil.
2. By means of the special adaptation of type MD998376 запрессуйте an epiploon in a casing against the stop, - track, that the epiploon has not appeared is overwound. At a corresponding complete set plant in a casing a separator (an oil aperture downwards).
3. Put hermetic on an interfaced surface, replace a sealing lining and establish an epiploon casing on the block.
4. Establish assemblage of a flywheel/privodnogo of a disk and transmission.
5. Connect a negative wire to the battery. Start the engine and check up it on presence of signs of development of leaks.
6. Check up level of impellent oil. In case of need make corresponding updating (see the Head of Adjustment and routine maintenance).