Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
- The engine
   - Removal/installation of the power unit, dismantle of components
      The general information
      Removal and engine installation
      Removal and installation of a cover of a head of cylinders
      Removal and installation of assemblages of a drive of valves
      Removal and thermostat installation
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and installation турбокомпрессора
      Removal and installation of a radiator of system of cooling (all models)
      Removal and installation of the fan of system of cooling of the engine
      Removal and installation of the water pump
      Removal and installation of a head of cylinders
      Removal and pallet installation картера the engine
      Removal and installation of the oil pump
      Removal and installation демпфера крутильных fluctuations of a cranked shaft
      Removal and installation of a cover of drive ГРМ and газораспределительного a belt
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of a drive of valves, check of a condition of components
      Removal and installation of a balancing shaft
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of a flywheel/privodnogo of a disk
   + Regenerative repair of the engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and installation of the fan of system of cooling of the engine

Installation details вентиляторных assemblages on models Diamante

1 — the Drain gate
2 — a radiator Cover
3 — Pouring a tube
4 — the Broad tank
5 — Top радиаторный a hose
6 — Bottom радиаторный a hose
7 — Штуцерное connection of a line of cooling ATF
8 — Штуцерное connection of a line of cooling ATF

9 — the Pillow of the top support
10 — radiator Assemblage
11 — the Pillow of the bottom support
12 — Assemblage of the fan of the condenser of a central air of air
13 — Приводной the electromotor
14 — Крыльчатка
15 — Приводной the electromotor
16 — the Casing


Except models Diamante

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Empty cooling system.

In order to avoid reception of burns, start performance of the listed works only after definitive cooling of system! Do not suppose antifreeze hit on open sites of a body and the painted surfaces of the car. Casually got splashes immediately wash off plentiful quantity of water. Remember that antifreeze is extremely a toxic liquid and its hit in an organism even in small amounts is fraught with the most serious consequences (up to a lethal outcome). Never leave antifreeze stored in leaky closed container and immediately collect cooling liquid spilt on a floor. Remember that the sweetish smell of antifreeze can draw to itself attention of children and animals. About ways recyclings of the fulfilled cooling liquid consult at any station of car-care centre. In many regions of the world special points on reception of a various sort of working off are equipped. At all do not merge an old cooling liquid in the water drain and on the earth!

3. Disconnect переливную a tube and top радиаторный a hose.
4. On models with АТ disconnect lines of cooling ATF (at once закупорьте the open ends of hoses and unions).
5. Disconnect electroconducting from the fan of system of cooling of the engine.
6. Turn out fixing bolts and remove from the car the fan in gathering with a protective casing.

7. Release a fastening nut крыльчатки and remove last from a shaft приводного the motor.
8. Turn out fixing screws and remove the electromotor from an assemblage casing.


Installation

 PERFORMANCE ORDER

1. Establish the electromotor on an assemblage casing, screw and tighten fixing bolts.
2. Further operate in an order, the return to an order of dismantle of components.
3. In summary fill in in cooling system necessary quantity of a fresh mix (see the Head of Adjustment and routine maintenance), connect a negative wire to the battery and check up serviceability of functioning of the fan (ов).


Models Diamante

Removal

 PERFORMANCE ORDER

1. Installation details вентиляторной assemblages on models Diamante are presented on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Empty cooling system.

In order to avoid reception of burns, start performance of the listed works only after definitive cooling of system! Do not suppose antifreeze hit on open sites of a body and the painted surfaces of the car. Casually got splashes immediately wash off plentiful quantity of water. Remember that antifreeze is extremely a toxic liquid and its hit in an organism even in small amounts is fraught with the most serious consequences (up to a lethal outcome). Never leave antifreeze stored in leaky closed container and immediately collect cooling liquid spilt on a floor. Remember that the sweetish smell of antifreeze can draw to itself attention of children and animals. About ways recyclings of the fulfilled cooling liquid consult at any station of car-care centre. In many regions of the world special points on reception of a various sort of working off are equipped. At all do not merge an old cooling liquid in the water drain and on the earth!

4. Disconnect electroconducting from the fan and радиаторного the gauge.

Usually electric sockets of the given components have tight execution, - try not to damage a detail of a design of assemblage.

5. Disconnect from a radiator the top hose and remove a broad tank.
6. Turn out fixing screws and remove вентиляторную assemblage.

On the given models possibility of removal of fans of system of cooling and an air conditioning separately is provided.

7. In case of need dismantle крыльчатку and приводной the electromotor.


Installation

 PERFORMANCE ORDER

1. Installation is made in an order, the return to an order of dismantle of components.
2. In summary fill in in cooling system necessary quantity of a fresh mix (see the Head of Adjustment and routine maintenance), connect a negative wire to the battery and check up serviceability of functioning of the fan (ов).