Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
- Brake system
   Specifications
   Replacement of the gauge-switch of stoplights
   Removal and installation ГТЦ
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning/tightness, removal and installation of the vacuum amplifier of brakes
   Removal and valve-regulator installation
   Removal and installation of brake lines
   Prorolling of brake system
   Disk brake mechanisms - the general information
   Estimation of a condition brake колодок
   Replacement колодок disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Regenerative repair of a support of the disk brake mechanism
   Removal, check of a condition and installation of a brake disk
   Drum-type brake mechanisms - the general information
   Removal, installation and check of a condition of a brake drum
   Check of a condition of brake boots
   Removal and installation of brake boots
   Adjustment of drum-type brake mechanisms
   Removal, regenerative repair and installation of wheel cylinders
   Removal and cable installation (ов) a drive of a lay brake
   Adjustment of a lay brake
   Removal and installation of frictional boots of a lay brake (model with disk brake mechanisms of back wheels)
   System of antiblocking of brakes (ABS) - the general information, a problem diagnostics and codes of malfunctions
   Removal and installation of the hydraulic modulator
   Removal and installation of the block of management ABS
   Removal and installation of wheel gauges
   Removal and installation of gauges of accelerations (G-gauges)
   Replacement of rotors of wheel gauges
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and installation of brake lines

Remember that the brake liquid merged from a path is not subject to a reuse!


Rules of service of lines of a hydraulic path

 PERFORMANCE ORDER

1. Check of a condition of metal and rubber brake lines should be made on a regular basis according to the schedule of routine maintenance of the car (see the Head of Adjustment and routine maintenance). Attentively examine all lines of a brake path on presence of mechanical damages and signs of development of leaks. Deformation of tubes can lead to infringement of their passableness, that in this case is fraught with infringement of efficiency of functioning of brake system (up to full refusal of a corresponding contour). Rubber hoses should be checked on presence of cracks, cuts, attritions, swellings and other signs of destruction of protective armature.

2. At a detachment of brake lines it is necessary to give special attention to cleanliness observance, - before undocking carefully smooth out a surface штуцерных sockets (use a brush and special cleaners). Right after detachments of lines stop up their open ends in order to avoid hit in a dirt and moisture path.

3. Before installation replaceable sections should be washed out a pure brake liquid.


Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. For the purpose of providing of access to a brake line requiring service remove a corresponding wheel.
4. Carefully (with application of a special cleaner) wipe subject to a detachment штуцерные sockets and surfaces surrounding them.
5. Prepare drain capacity and rags for gathering of a spilt brake liquid.

6. Undocking штуцерного a socket is made by means of two keys, one of which (накидной with a cutting head) is put on on штуцерную a nut, and the second is used for keeping of a reciprocal part of a joint from проворачивания. Application of two keys will allow to avoid the extremely undesirable deformations of a hydraulic line and union damage.

7. Any, used in штуцерных sockets sealing washers are subject to replacement without fail!

8. Having moved drain capacity, disconnect the second end of served section of a brake path (also take advantage of two keys).

9. Liberate the disconnected line from intermediate clamps and remove it from the car. At once закупорьте the open ends of the disunited path.


Installation

 PERFORMANCE ORDER

1. At installation of replaceable section of a brake line to begin follows from connection of that its end which is more removed from the main cylinder. At наживлении штуцерной nuts track, that there was no it перекашивания, fraught with carving failure.
2. The tightening штуцерных sockets also is made by means of two keys.
3. Having established replaceable section, make sure, that it does not adjoin to moving elements of a suspension bracket / a steering drive (safe it is considered removal not less than 13 mm).
4. Track, that the line has been fixed in all provided intermediate clamps / basic arms.

At installation of flexible brake hoses watch, that they have not appeared are overwound.

5. Establish all components acting in film for the purpose of providing of access, then lower the car on the earth.
6. Add in tank GTTS necessary quantity of a fresh hydraulic liquid (see the Head of Adjustment and routine maintenance), and pump over brake system (the Section Prorolling of brake system see).