Mitsubishi Galant

1. Check up course freedom приводного a cable of a lay brake.
2. Counting quantity of clicks of a ratchet, cock the lever of a lay brake with effort 200 Н. Recommended value makes 5 ч 7 clicks.
3. In case of need make adjustment.

4. Access to an adjusting nut is possible from within floor section of the central console.

5. Ослабьте a lock nut of a rod тросовой assemblages.
6. Rotation of an adjusting nut achieve demanded result (by quantity of clicks of a ratchet). Track, that between an adjusting nut and the lever it was not formed люфт, then tighten a lock nut.

Be not overzealous, - excessively hard tension of a cable can lead to failure of automatic regulators of brake mechanisms, and also “прихватыванию” brakes!

7. Having finished adjustment of a course of the lever, поддомкратьте a back of the car also check up freedom of rotation of back wheels at the released lay brake.
8. Check up reliability of keeping of the car a lay brake on a bias.

2. Before to start adjustment тросового a drive, it is necessary to adjust boots of a lay brake for what поддомкратьте the car and establish it on props. Take from a brake disk заглушку, remove a support and tie up its wire to suspension bracket elements, not disconnecting a hydraulic line. Rotating a self-regulator castor the suitable tool, block rotation of a brake disk. Turn off a castor on five рисок in the opposite direction and make sure, that the disk is turned with easy resistance. Establish into place a support and check up serviceability of functioning of the brake mechanism.
3. Having finished adjustment of frictional boots of a lay brake, start adjustment тросового a drive.
4. Rotation of an adjusting nut achieve demanded quantity of clicks of a ratchet at raising of the lever of a lay brake with certain effort.
5. Поддомкратьте a back of the car also establish it on props and check up freedom of rotation of back wheels at the released lay brake. In case of need release little bit adjusting nut.

1. Requirements by quantity of clicks of a ratchet at raising of the lever with effort 200 Н remain former (5 ч 7 clicks). In case of need make corresponding updating.
2. Remove an internal floor-mat of floor section of the central console.
3. Having released an adjusting nut on the rod end тросовой assemblages, ослабьте a drive tension.
4. At the engine working on single turns five-six times firmly squeeze out a pedal of a foot brake, - the pedal course should be stabilised, that confirms serviceability of functioning of the mechanism of an automatic regulator and correctness of installation of a backlash between boots and a working surface of a brake drum.
5. Further, in a standard manner (the previous subsection see) execute adjustment тросового a drive. Поддомкратьте a back of the car also check up freedom of rotation of back wheels at the released lay brake.

1. On models Diamante raising of the lever of a lay brake with effort 200 Н should be accompanied by three-five clicks of a ratchet.
2. Check up correctness of adjustment of boots of a lay brake, in case of need make corresponding updating.
3. Remove floor section of the central console. Release the lever of a lay brake and give a regulator counternut in the basis of lever assemblage.
4. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel and take заглушку from a brake disk.
5. Remove a brake support and, not disconnecting a hydraulic line, tie up its wire to a suspension bracket element.
6. Rotating a self-regulator castor the suitable tool, block rotation of a brake disk. Turn off a castor on five рисок in the opposite direction and make sure, that the disk is turned with easy resistance.
7. Establish into place a support and check up serviceability of functioning of the brake mechanism.
8. Having finished adjustment of frictional boots of a lay brake, start adjustment тросового a drive.
9. Rotation of an adjusting nut achieve demanded quantity of clicks of a ratchet at raising of the lever of a lay brake with certain effort.
10. Поддомкратьте a back of the car also establish it on props and check up freedom of rotation of back wheels at the released lay brake. In case of need release little bit adjusting nut.