Mitsubishi Galant

1990-2001 of release

Repair and car operation

Removal, installation and check of a condition of a brake drum

Design of the drum-type brake mechanism used on models Mirage on 1992 вып.

1 — the Cover ступичной nuts
2 — Ступичная a nut
3 — the Internal holder of the external bearing
4 — the Brake drum
5 — the Spring of fastening of a boot to the regulator lever
6 — the regulator Lever
7 — Assemblage of an automatic regulator
8 — the Bottom coupling spring
9 — Plates of directing springs
10 — Directing springs of boots
11 — the Top coupling spring

12 — the Brake boot
13 — Assemblage of a boot with анкерным in knot
14 — the Holder
15 — the Wavy washer
16 — the Executive lever of a drive of a lay brake
17 — the Brake boot
18 — Анкерный a finger
19 — the Brake tube
20 — the Lock ring
21 — the Brake board

Design of the drum-type brake mechanism used on models Galant and Mirage since 1993 вып.


1 — the Brake drum 2 — the Spring of fastening of a boot to the regulator lever 3 — the regulator Lever 4 — Assemblage of an automatic regulator 5 — the Bottom coupling spring 6 — Plates of directing springs 7 — Directing springs of boots 8 — Plates of directing springs 9 — the Top coupling spring 10 — the Brake boot with a frictional overlay	11 — Assemblage of a brake boot with the adjusting lever 12 — the Holder 13 — the Wavy washer 14 — the Executive lever of a drive of a lay brake 15 — the Brake boot with a frictional overlay 16 — Анкерный a finger 17 — the Brake tube 18 — the Lock ring 19 — Ступичная assemblage 20 — the Brake board

Remember that developed in the course of work of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, - apply only firm cleaners or methyl spirit!

Models Mirage on 1992 of вып.

Removal

PERFORMANCE ORDER

1. A design of the drum-type brake mechanism used on models Mirage on 1992 вып. It is presented on an illustration.
2. Поддомкратьте the car also establish it on props.
3. Remove a corresponding back wheel.
4. Remove a dustproof cover ступичной nuts.
5. Give самоконтрящуюся ступичную a nut.
6. Remove the external wheel bearing.
7. Remove from a spindle a brake drum in gathering with the internal wheel bearing.
8. Remove an epiploon.

Installation

PERFORMANCE ORDER

1. For validity check to further use самоконтрящейся nuts screw it on a spindle so that the end of the last left outside approximately on 3 mm. Measure twisting moment of resistance to nut rotation counter-clockwise. The result of measurement makes less than 5.5 H•м, the nut is subject to replacement.
2. Grease and establish the internal bearing.
3. Establish a new epiploon.
4. Put on a spindle a brake drum.
5. Grease and establish the external wheel bearing.
6. Tighten самоконтрящуюся ступичную a nut with demanded effort (150 ч 200 H•м).
7. Establish a protective cover.

Condition check

PERFORMANCE ORDER

1. Measure internal diameter of the brake drum removed from the car, - for the purpose of revealing of signs of ovality measurement should be made in several points.

2. If the result of measurement exceeds maximum permissible value (231 mm), replace a drum complete with boots (see Has undressed Removal and installation of brake boots).

Models Galant and Mirage since 1993 вып.

Removal

PERFORMANCE ORDER

1. A design of the drum-type brake mechanism used on models Galant and Mirage since 1993 вып. It is presented on an illustration.
2. Поддомкратьте the car also establish it on props.
3. Remove a corresponding back wheel.
4. Ослабьте an adjusting nut of a drive of a lay brake.

5. Having pulled on itself, remove a brake drum with ступичной assemblages, - in case of need обстучите assemblage by a hammer with soft brisk for the purpose of its clearing. If the disk at boiled and does not give in to removal, screw in specially provided two carving apertures in its obverse surface pair of bolts approaching on the size and, gradually tightening them, release a drum.

Installation

PERFORMANCE ORDER

1. Establish a drum on a nave.
2. Establish a wheel adjust a drive of a lay brake.
3. Lower the car on the earth.