Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and трансмиссионная a line
- Brake system
   Specifications
   Replacement of the gauge-switch of stoplights
   Removal and installation ГТЦ
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning/tightness, removal and installation of the vacuum amplifier of brakes
   Removal and valve-regulator installation
   Removal and installation of brake lines
   Prorolling of brake system
   Disk brake mechanisms - the general information
   Estimation of a condition brake колодок
   Replacement колодок disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Regenerative repair of a support of the disk brake mechanism
   Removal, check of a condition and installation of a brake disk
   Drum-type brake mechanisms - the general information
   Removal, installation and check of a condition of a brake drum
   Check of a condition of brake boots
   Removal and installation of brake boots
   Adjustment of drum-type brake mechanisms
   Removal, regenerative repair and installation of wheel cylinders
   Removal and cable installation (ов) a drive of a lay brake
   Adjustment of a lay brake
   Removal and installation of frictional boots of a lay brake (model with disk brake mechanisms of back wheels)
   System of antiblocking of brakes (ABS) - the general information, a problem diagnostics and codes of malfunctions
   Removal and installation of the hydraulic modulator
   Removal and installation of the block of management ABS
   Removal and installation of wheel gauges
   Removal and installation of gauges of accelerations (G-gauges)
   Replacement of rotors of wheel gauges
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation ГТЦ

Details of installation ГТЦ on models Diamante

1 — Assemblage ГТЦ
2 — the Vacuum hose (with the built in control valve)
3 — the Pin of fastening of a cutting finger of a rod of a pusher
4 — the Washer

5 — Шплинт
6 — the Vacuum amplifier
7 — the Sealing lining


Details of installation ГТЦ on models Galant of 1994-1997 of вып.

1 — the Union of connection of a brake tube
2 — the Socket of electroconducting of the gauge of level of a brake liquid
3 — Assemblage ГТЦ
4 — the Vacuum hose (with the built in control valve)
5 — the Union

6 — Шплинт
7 — the Pin of fastening of a cutting finger of a rod of a pusher
8 — the Vacuum amplifier
9 — the Sealing lining


Failed ГТЦ is subject to replacement. Manufacturers do not recommend to undertake attempt of carrying out of regenerative repair of the main brake cylinder.


The brake liquid is among aggressive chemical compounds and at contact with кузовными panels destroys a paint and varnish covering. Before to start procedure performance cover wings and the panel передка the car with special covers, or simply old blankets.


Removal

 PERFORMANCE ORDER

1. Details of installation of the main brake cylinder are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Remove a plastic cover, by means of a syringe or a rubber pear pump out from tank GTTS as it is possible большее quantity of a brake liquid, then establish a cover into place.

4. Disconnect from ГТЦ and at once закупорьте brake lines.

5. Disconnect electroconducting from the gauge-switch of level of a brake liquid, release fixture and remove tank GTTS.

6. On models with РКПП remove a basic arm of the tank of the main hydraulic cylinder of coupling.
7. Give fixing nuts and remove ГТЦ from assemblage of the vacuum amplifier of brakes.


Installation

 PERFORMANCE ORDER

1. Execute adjustment of a backlash And between an end face of a rod of a pusher of the vacuum amplifier and a nest bottom in primary piston GTTS. The Rating value makes 0.65 0.86 mm, at depth of depression in the amplifier 67 кПа the backlash will be reduced to 0.1 0.3 mm.

2. Establish ГТЦ on assemblage of the vacuum amplifier of brakes. Screw fixing nuts and tighten them with demanded effort (10 H•м).
3. Establish into place and fix tank GTTS.
4. Connect to the tank hydraulic lines and electroconducting of the gauge of level of a brake liquid.
5. The further installation is made as it should be the return to an order of dismantle of components.
6. In summary fill in in the tank fresh brake liquid DOT 3, pump over a hydraulic path (the Section Prorolling of brake system see) and execute adjustment of a pedal of a foot brake (the Section Adjustment of a pedal of a foot brake see).