Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and трансмиссионная a line
- Brake system
   Specifications
   Replacement of the gauge-switch of stoplights
   Removal and installation ГТЦ
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning/tightness, removal and installation of the vacuum amplifier of brakes
   Removal and valve-regulator installation
   Removal and installation of brake lines
   Prorolling of brake system
   Disk brake mechanisms - the general information
   Estimation of a condition brake колодок
   Replacement колодок disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Regenerative repair of a support of the disk brake mechanism
   Removal, check of a condition and installation of a brake disk
   Drum-type brake mechanisms - the general information
   Removal, installation and check of a condition of a brake drum
   Check of a condition of brake boots
   Removal and installation of brake boots
   Adjustment of drum-type brake mechanisms
   Removal, regenerative repair and installation of wheel cylinders
   Removal and cable installation (ов) a drive of a lay brake
   Adjustment of a lay brake
   Removal and installation of frictional boots of a lay brake (model with disk brake mechanisms of back wheels)
   System of antiblocking of brakes (ABS) - the general information, a problem diagnostics and codes of malfunctions
   Removal and installation of the hydraulic modulator
   Removal and installation of the block of management ABS
   Removal and installation of wheel gauges
   Removal and installation of gauges of accelerations (G-gauges)
   Replacement of rotors of wheel gauges
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation of brake boots

Remember that developed in the course of work of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, - apply only firm cleaners or methyl spirit!


Make service of brake assemblages serially, - in case of need the second can be used as the sample.


Models Mirage on 1992 вып.

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props.
2. Remove back wheels.
3. Remove a brake drum.
4. Before to start dismantle of components, try to remember adjusting positions of all springs and clamps.
5. Remove the top coupling spring.
6. Remove a spring of fastening of a boot to the regulator lever, then remove regulator assemblage.
7. Remove clamps of directing springs and dismantle brake boots, having disconnected from back a cable of a drive of a lay brake.


Installation

 PERFORMANCE ORDER

1. Carefully clear and dry a brake board, check up smoothness of its acting contact surfaces, - presence of roughnesses is fraught with jamming of boots.
2. Grease contact surfaces of a board and анкерные fingers of boots литиевой with greasing.
3. Remove and carefully clean other components of the brake mechanism. Grease a carving part of an adjusting castor with antitaking hermetic and transfer all details on new башмачные assemblages.
4. Connect to corresponding boot a cable of a drive of a lay brake.
5. Fix boots on a brake board and, operating as it should be the return to a dismantle order, establish fixing components of brake assemblage.
6. Adjust boots so that the brake drum sat down on them with easy resistance (the Section Adjustment of drum-type brake mechanisms see). Establish a drum.
7. Screw new ступичную a nut and tighten it with demanded effort (180 Nanometers).
8. Establish a protective cover of the wheel bearing and adjust boots of back brake mechanisms.


Models Galant and Mirage since 1993 вып.

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props.
2. Remove back wheels and brake drums (see Has undressed Removal, installation and check of a condition of a brake drum).

3. Remove a spring of fastening of a boot to the regulator lever.

4. Remove the adjusting lever.

5. Remove assemblage of an automatic regulator.

6. Remove the bottom coupling spring.

7. Remove clamps and take directing springs of boots.

8. Remove the top coupling spring.
9. Remove brake boots, - disconnect from the executive lever on a back boot a cable of a drive of a lay brake.

10. Remove the executive lever of a drive of a lay brake from an old boot.


Installation

 PERFORMANCE ORDER

1. Carefully wipe a brake board and process contact surfaces of persistent ledges special brake greasing.

2. Transfer the executive lever of a drive of a lay brake on assemblage of a new boot (back), - track correctness of installation of a wavy washer.

3. Clean assemblage of an automatic regulator and accurately grease its carving part with special brake greasing.
4. Connect a cable of a drive of a lay brake to the executive lever of a back boot.
5. Transfer assemblage of a back boot on a brake board and establish directing spring and анкерный a finger.
6. Operating in a similar manner, establish on the regular place a forward boot.
7. Place between boots regulator assemblage.
8. Establish the top coupling spring.
9. Establish the bottom coupling spring.
10. Establish the regulator lever.
11. Establish a spring of fastening of a boot to the regulator lever.
12. Establish a returnable spring of the lever. Adjust boots and establish a brake drum (see Has undressed Removal, installation and check of a condition of a brake drum).
13. Operating in a similar manner, replace boots of the brake mechanism of an opposite wheel.
14. Establish wheels and lower the car on the earth.