Mitsubishi Galant

1. Details of installation of gauges of turns of forward wheels on models Mirage are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! In order to avoid operation of pillows of safety start gauge dismantle after not less than 90 seconds after battery switching-off.

3. Поддомкратьте the car also establish it on props. Remove a corresponding wheel.
4. Remove локер protection of a wheel arch.
5. Disconnect from the wheel gauge electroconducting.
6. Remove clamps of fastening of a plait of electroconducting of the gauge.
7. Remove the gauge from a basic arm.

1. Establish the gauge on a basic arm and tighten a fixing bolt.
2. Establish clamps of fastening of a plait of electroconducting.
3. Connect electroconducting to the gauge.
4. Connect a negative wire to the battery.

1. Details of installation of gauges of turns of back wheels on models Mirage are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! In order to avoid operation of pillows of safety start gauge dismantle after not less than 90 seconds after battery switching-off.

3. Поддомкратьте the car also establish it on props. Remove a corresponding wheel.
4. Disconnect from the wheel gauge electroconducting.
5. Remove clamps of fastening of a plait of electroconducting of the gauge.
6. Turn out a fixing bolt and remove the wheel gauge.

1. Establish the gauge on the regular place and freely tighten a fixing bolt.
2. Establish clamps of fastening of a plait of electroconducting.
3. Connect electroconducting to the gauge.

4. By means of not magnetic щупа лезвийного type adjust a backlash between the gauge and its rotor, - demanded value makes 0.3 — 0.9 mm.

5. Definitively tighten fixture and once again check up correctness of installation of a backlash. In case of need repeat adjustment.
6. Connect a negative wire to the battery.

1. Details of installation of wheel gauges on models Galant are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! In order to avoid operation of pillows of safety start gauge dismantle after not less than 90 seconds after battery switching-off.

3. Поддомкратьте the car also establish it on props. Remove a corresponding forward wheel.
4. Remove локер protection of a wheel arch.
5. Disconnect from the wheel gauge electroconducting.
6. Turn out coupling bolts and remove collars of fastening of a plait of electroconducting of the gauge.
7. Turn out a fixing bolt and remove the wheel gauge.

1. Establish the gauge on the regular place and tighten a fixing bolt.

The backlash between the gauge and its rotor is not subject to adjustment, however should be checked up. Demanded value makes 28.2 ч 28.4 mm. At an exit of result of change for limits of an admissible range replace the gauge or a rotor.

2. Fix burn down gauge electroconductings by bandage collars, - strongly tighten coupling bolts.
3. Connect electroconducting to the gauge.
4. Establish локер protection of a wheel arch.
5. Establish into place a wheel and lower the car on the earth.
6. Connect a negative wire to the battery.

1. Details of installation of wheel gauges are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! In order to avoid operation of pillows of safety start gauge dismantle after not less than 90 seconds after battery switching-off.

3. Поддомкратьте the car also establish it on props. Remove a corresponding forward wheel.
4. Disconnect from the wheel gauge electroconducting.
5. Turn out coupling bolts and remove collars of fastening of a plait of electroconducting of the gauge.
6. Turn out a fixing bolt and remove the wheel gauge.

1. Establish the gauge on the regular place and tighten a fixing bolt.

The backlash between the gauge and its rotor is not subject to adjustment, however should be checked up. Demanded value makes 28.2 ч 28.4 mm. At an exit of result of change for limits of an admissible range replace the gauge or a rotor.

2. Fix burn down gauge electroconductings by bandage collars, - strongly tighten coupling bolts.
3. Connect electroconducting to the gauge.
4. Establish into place a wheel and lower the car on the earth.
5. Connect a negative wire to the battery.

1. Details of installation of gauges of turns of forward wheels on models Diamante are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! In order to avoid operation of pillows of safety start gauge dismantle after not less than 90 seconds after battery switching-off.

3. Поддомкратьте the car also establish it on props. Remove a corresponding wheel.
4. Remove локер protection of a wheel arch.
5. Disconnect from the wheel gauge electroconducting.
6. Remove clamps of fastening of a plait of electroconducting of the gauge.
7. Remove the wheel gauge.

1. Establish the gauge on the regular place and tighten it with demanded effort (12 H•м).
2. Establish clamps of fastening of a plait of electroconducting.
3. Connect electroconducting to the gauge.
4. Connect a negative wire to the battery.

1. Details of installation of gauges of turns of back wheels on models Mirage are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! In order to avoid operation of pillows of safety start gauge dismantle after not less than 90 seconds after battery switching-off.

3. Поддомкратьте the car also establish it on props. Remove a corresponding wheel.
4. Disconnect from the wheel gauge electroconducting.
5. Remove clamps of fastening of a plait of electroconducting of the gauge.
6. On all-wheel drive (AWD) models remove тросовый a bandage.
7. Turn out a fixing bolt and remove the wheel gauge together with a sealing ring.

1. Establish the gauge on the regular place (do not forget to replace a sealing ring) and tighten it with demanded effort (12 H•м).
2. Establish clamps of fastening of a plait of electroconducting.
3. Establish тросовый a bandage.
4. Connect electroconducting to the gauge.
5. Connect a negative wire to the battery.