Mitsubishi Galant

1. Приводные belts are located in a forward part of the power unit and play the important role in functioning of the engine and many other things of car systems. Eventually belts wear out and should look round regularly according to the schedule of routine maintenance of the car in order to avoid the serious engine failures which correction of consequences can rise to the owner of the car in копеечку.
2. The quantity used on concrete model of the car приводных belts depends on a vehicle complete set auxiliary units. Belts are used for a drive of the generator, steering and water pumps, and also the compressor of the conditioner of air. Depending on character of an arrangement of pulleys by one belt it can be put in action more than one unit.

3. Muffle the engine, open a cowl and find приводные belts.

4. Highlighting itself a small lamp, fingers feel belts on all their length, checking on presence of cracks and stratifications. Presence on a belt of attritions, заполированных to shine of sites and other obvious defects is inadmissible also. Examine belts from both parties for what overwind them. Defective belts are subject to replacement without fail. Check up a condition of edges on the bottom party of belts, - they should have identical depth in the absence of deformation signs.

5. The estimation of effort of a tension of a belt can be made by нажимания on it the big finger on a site in the middle between two next pulleys. Pressing should be firm enough. In parametre, характеризирующим the effort of a tension of a belt, is size of its deflection at нажимании. As a rule, if pulleys defend from each other on distance from 180 to 280 mm, the deflection size should make 6.4 mm, between pulleys in 305 ч 405 mm correspond to distance a deflection in 12.5 mm - for клиновидного a belt, and 6.4 mm - for ручейкового.

1. The tension приводного a belt with excessive effort can lead to premature failure шкивных bearings of corresponding units whereas, on the other hand, too weak tension leads to fast deterioration actually a belt. Regularly check efforts of a tension of belts of a drive of all auxiliary units established on the car.
2. As a rule, updating of effort of a tension of a belt (easing/strengthening) is carried out by displacement in the corresponding party of the hinged auxiliary unit/assemblage resulted by a belt натяжителя.
3. Usually on each of used on the engine приводных belts it is necessary on one component which fixture is carried out by means of axial/lock and adjusting bolts. The Axial/lock bolt is released, then the adjusting rotates in the corresponding party.
4. For easing of effort of a tension of a belt the component should be displaced towards the engine and on the contrary. Having finished updating, track reliability of a tightening of bolts. For displacement of some hinged units it is necessary to take advantage of the lever, - observe extreme care, try not to damage the resulted device.

The scheme of a lining of belts of a drive of auxiliary units on the given models is presented on an illustration.

3. Throw with a new belt corresponding pulleys and, rotating an adjusting bolt clockwise, make adjustment of its tension (see above).
4. Having finished adjustment, strongly tighten a lock bolt and a fixing nut.

1. Remove a generating belt (see above).
2. Ослабьте adjusting bolts of the steering pump.
3. Release fixing bolt from the back party of a basic arm of pump assemblage.
4. Wring out the pump to the engine and remove a belt.

5. Throw with a new belt corresponding pulleys.
6. Having wrung out pump assemblage from the engine, achieve demanded effort of a tension of a belt (see above).
7. Strongly tighten adjusting bolts, then - a fixing bolt on the back party of a basic arm of the pump.
8. Establish into place a generating belt (see above).

1. Ослабьте a pulley натяжителя also remove a belt of a drive of compressor K/V from the engine.
2. Installation is made upside-down.

1. The scheme of a lining of belts of a drive of auxiliary units on the given models is presented on illustrations (see above).
2. Поддомкратьте the car also establish it on props. At a corresponding complete set remove protection elements картера.
3. Release fixing nut of a pulley натяжителя and, rotating an adjusting bolt, ослабьте effort of a tension of a belt.
4. Throw off a belt from pulleys and remove it from the engine.
5. Put on a new belt pulleys of a cranked shaft, the generator and (at a corresponding complete set) compressor K/V and get it under tension and intermediate rollers.
6. Rotating an adjusting bolt натяжителя, achieve demanded effort of a tension of a belt (see above).
7. Strongly tighten fixing nut.
8. If removed, establish into place protection elements картера and lower the car on the earth.

1. Disconnect a negative wire from the battery and, before to start procedure performance, wait not less than 90 seconds for the purpose of deactivation of pillows of safety.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props. Remove protection elements картера.
3. Remove a belt of a drive of generator/compressor K/V.
4. Lower the car on the earth and remove assemblage of connecting draught of the pump of a control system by speed (темпостата).
5. Pass a hose of system of hydrostrengthening of a wheel under the oil tank.
6. Release fixing bolts of a pulley натяжителя, then remove a belt of a drive of the steering pump from the engine.
7. Throw with a new belt corresponding pulleys.
8. Pass a collar of strengthening of a drive of a face key (or other suitable tool) in an aperture in an end face of an arm of a pulley натяжителя and, having wrung out assemblage of the last, achieve demanded effort of a tension of a belt (see above).
9. Tighten fixing bolts.
10. Поддомкратьте the car also establish it on props. Establish into place a belt of a drive of generator/compressor K/V.
11. Establish into place protection elements картера and lower the car on the earth.
12. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Ослабьте a lock bolt on a pulley натяжителя a belt of drive К/В.
3. Rotating an adjusting bolt of a pulley, ослабьте effort of a tension of a belt.
4. Throw off a belt from pulleys and remove it from the engine.
5. Ослабьте a counternut on a pulley натяжителя a belt of a drive of the generator / the steering pump.
6. Rotation of an adjusting bolt ослабьте effort of a tension of a belt also remove last from the engine.
7. At first always it is necessary to establish a belt of a drive of the generator / the steering pump and only then - compressor K/V belt.
8. Rotation of adjusting bolts achieve demanded effort of a tension of both belts (see above). Then tighten fixing fixture (a pulley nut натяжителя a belt of a drive of the generator / the steering pump it is necessary to tighten of 50 Nanometers with effort).
9. Connect a negative wire to the battery.