Mitsubishi Galant

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. Disassemble racks of the stabilizer of cross-section stability: give counternuts, take cups, rubber and plugs. Turn out bolts of fastening of racks.
4. Remove a reception pipe of system of release of the fulfilled gases.
5. Hang out the power unit on лебедке from above. Turn out four bolts of fastening of the central beam.
6. Remove both support of assemblage реечного the mechanism of a steering drive.
7. Disconnect from the central beam the bottom lever of a suspension bracket.
8. Prop up a beam a jack, turn out fixing bolts and lower assemblage, having provided necessary free space for extraction of a bar of the stabilizer of cross-section stability.
9. Give fixture and take a bar of the stabilizer of cross-section stability from under the car.

1. Installation is made upside-down.
2. Tighten bolts of fixing collars of a bar of the stabilizer of cross-section stability with effort 22 H•м.
3. At assemblage of racks of the stabilizer track, that the size выступания a bolt made 22 mm.
4. Lower the car on the earth and connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. Disconnect a reception pipe of system of release of the fulfilled gases from a final collector (remove a sealing lining). Tie up a pipe so that it did not stir to dismantle of the stabilizer of cross-section stability.

Try not to suppose перегибания flexible муфты reception section of a final path under a corner more than in some degrees!

4. Turn out back bolts of fastening of the central beam.
5. Turn out bolts of fastening of racks of the stabilizer of cross-section stability.

On racks of spherical type отпускания самоконтрящейся nuts шаровый should be kept a finger in process from проворачивания with the help шестигранного a key.

6. Turn out bolts of fixing collars of a bar of the stabilizer of cross-section stability.
7. Delay both ends of a bar back on the car, then liberate its right end from under the bottom lever of a suspension bracket. Trace liberate the left end of a bar from under the opposite lever. Having pulled a bar to the right, take it from under the car.
8. Estimate degree of deterioration of all rubber plugs, defective components replace.
9. Check up a condition of a bar of the stabilizer. In case of need make replacement.

1. Get a bar of the stabilizer of cross-section stability on the regular place.
2. Establish collars of fastening of a bar (pay attention to identification marks). Level components, then strongly tighten fixture.
3. At a tightening of fixture of racks of spherical type take advantage of two keys. Track, that the size выступания a bolt over a nut made 16 ч 18 mm.
4. Connect a reception pipe to a final collector (do not forget to replace a sealing lining). Tighten самоконтрящиеся nuts of a joint with demanded effort (40 H•м).
5. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Disconnect a reception pipe of system of release of the fulfilled gases from a final collector (remove a sealing lining).
3. Remove central кницу and assemblage of a distributing box.
4. Remove a rack of the stabilizer of cross-section stability, - at отдавании nuts spherical hairpins of hinges should be kept from проворачивания the second key.
5. Turn out a fixing bolt and remove an assembly collar of the stabilizer of cross-section stability with the rubber plug.
6. Disconnect the stabilizer from the right bottom lever of a suspension bracket.
7. Take the left section of a bar of the stabilizer through space between a power shaft and the bottom lever. The right section is taken from under the corresponding bottom lever.

1. Establish a stabilizer bar on the regular place.
2. Temporarily tighten fixture of an assembly collar. Level end faces of the rubber plug concerning the adjusting labels put on a bar, then tighten fixture definitively.
3. Screw and tighten a bolt of an assembly collar.
4. Establish racks of the stabilizer and tighten their fixing nuts, - spherical hairpins are blocked from проворачивания by means of the second wrench. The bolt should act over a nut surface on size 16 ч 18 mm).
5. Establish assemblage of a distributing box and assembly кницу.
6. Establish the left bottom beam and tighten bolts of its fastening with demanded effort (80 H•м: back and 100 H•м: lobbies).

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. Release самоконтрящиеся nuts and remove racks of the stabilizer of cross-section stability.

4. Remove assembly collars of a bar of the stabilizer with rubber plugs.

5. Remove the stabilizer.
6. Estimate degree of deterioration of components, replace the failed knots.

1. Get a stabilizer bar on the regular place.
2. Freely establish assembly collars.
3. Level a bar so that its both landing labels have appeared on distance about 10 mm from the inside from collars.
4. Tighten bolts of fastening of collars with demanded effort (39 H•м).
5. Connect stabilizer racks to a bar and демпферным to plugs. Tighten lock nuts with demanded effort (39 H•м).
6. Lower the car on the earth and connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. Remove a reception pipe of system of release of the fulfilled gases and protection картера.
4. Remove the left and right bottom beams.
5. Remove a rack of the stabilizer of cross-section stability.
6. Release assembly collars and remove a stabilizer bar.

1. Get a stabilizer bar on the regular place and fix its assembly collars. Do not mix the left collar with right, - attentively study identification marks.

Before installation it is necessary to grease all rubber components of fixing knots.

2. Establish a rack of the stabilizer of cross-section stability.
3. Establish the bottom beams.
4. Establish a reception pipe of system of release of the fulfilled gases and protection elements картера.
5. Connect a negative wire to the battery.