Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment





Removal and installation подрулевого the combined switch

Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Onboard electric equipment see the Head). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation. In order to avoid system SRS damage, track, that the steering shaft was not turned after steering wheel removal. Block a column the ignition key at rectilinear position of forward wheels.


Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. At a corresponding complete set of the car make deactivation of a pillow of safety (the Onboard electric equipment see the Head).
3. Remove a steering wheel (see Has undressed Removal and steering wheel installation).
4. On models Diamante remove the handle отпускания the cowl lock.
5. Dismantle the knee emphasis located under a steering column. Remove the top and bottom sections of a casing of a steering column.
6. On models Diamante if it is required, remove knee having blown and a sleeve of giving of air in a foot well, then accurately disconnect electroconducting from assemblage подрулевого the combined switch.
7. On models Mirage disconnect all electroconducting, release a clamp and remove assemblage подрулевого the switch.
8. On models Galant at a corresponding complete set turn out four screws of fastening to assemblage подрулевого the switch of a sliding contact ring темпостата. Turn out two fixing screws and remove the switch.


Installation

 PERFORMANCE ORDER

1. Establish switch assemblage on the regular place and connect to it corresponding electroconducting, - track reliability защелкивания all provided clamps.
2. Establish sections of a casing of a steering column and a knee emphasis.
3. If removed, establish into place a sleeve of giving of air in a foot well and knee having blown.
4. Make sure, that forward wheels of the car remain in rectilinear position and establish into place a steering wheel (see Has undressed Removal and steering wheel installation).
5. Connect a negative wire to the battery and turn the ignition key in position ON, - on an instrument guard control lamp SRS should join for seven seconds.
6. Check up serviceability of functioning подрулевого the switch.