Mitsubishi Galant

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props, - wheels should appear completely torn off from the earth.
3. Disconnect from the bottom lever a rack of the stabilizer of cross-section stability.
4. Liberate a finger of the bottom spherical support from assemblage of a rotary fist.
5. Give a fixing nut and take a through bolt of fastening of an internal support of the lever to a frame.
6. Turn out back fixing bolts, at a corresponding complete set remove a collar.
7. In case of need remove the plug of a back rod.

1. If removed, establish on assemblage of the bottom lever the plug of a back rod.
2. Establish lever assemblage on the car and temporarily tighten a nut of a through bolt.
3. Establish a collar, bolts and replaceable nuts of a back support. Tighten bolts with effort 100 ч 120 H•м, nuts - 40 H•м.
4. Fill a finger of a spherical support in assemblage of a rotary fist and tighten a new fixing nut with demanded effort (60 ч 72 H•м).
5. Connect to the lever a rack of the stabilizer of cross-section stability.
6. Lower the car on the earth for a definitive tightening of fixture.
7. After all weight of the car will be transferred on a suspension bracket tighten nuts of through bolts of the bottom levers of a suspension bracket with demanded effort (102 ч 122 H•м).
8. Connect a negative wire to the battery.
9. Execute check and adjustment of corners of installation of forward wheels.

1. Details of installation of the bottom levers of a suspension bracket on models Galant 1994 ч 1998 of вып. Are shown on an accompanying illustration. Both spherical support are built in in bodies of the sections of the bottom lever and in case of their exit out of operation are subject to replacement in gathering with the last.
2. Поддомкратьте the car also establish it on props.

3. Give a nut of a bolt of fastening to cross-section section of the bottom lever демпферной shock-absorber plugs, take a bolt. Liberate fingers of the bottom spherical support from a rotary fist.

4. For removal of cross-section section of the lever it is necessary to dismantle arms of the bottom beam preliminary.
5. Give fixture of the internal end of cross-section section of the bottom lever and remove assemblage of last from the car.
6. Turn out two fixing bolts and remove jet section of the bottom lever.

1. Plant in assemblages of sections of the bottom lever rubber plugs.
2. Establish cross-section section of the bottom lever of a suspension bracket on the regular place. Fill an internal fixing bolt and temporarily tighten a new nut of its fastening.
3. Establish jet section of the lever.
4. Fill fingers of both spherical support in assemblage of a rotary fist. Screw new fixing nuts and tighten them with demanded effort (59 ч 71 H•м).
5. Lower the car on the earth and definitively tighten corresponding fixture of cross-section section with demanded effort (98 ч 118 H•м: an internal bolt and 88 H•м: a fastening bolt демпферной plugs).
6. With demanded effort (83 H•м) tighten bolts of fastening of jet section.
7. Establish into place arms of the bottom beam and tighten bolts of their fastening with effort 69 ч 78 H•м.
8. Make adjustment of corners of installation of forward wheels.

1. Details of installation of assemblage of the bottom lever of a suspension bracket on models Mirage are shown on an illustration.
2. Поддомкратьте the car also establish it on props. Remove a corresponding forward wheel.
3. Remove from assemblage of the bottom lever of a suspension bracket of a rack of the stabilizer of cross-section stability, or give nuts and take fixing bolts. Remove cups and plugs of connecting knots.
4. Liberate from a rotary fist a finger of a spherical support.
5. Give a nut and take an internal bolt of fastening of assemblage of the bottom lever.
6. Turn out bolts of a back fixing collar and remove assemblage of the bottom support from the car.

1. Establish assemblage of the bottom lever on the regular place and tighten a nut of an internal fixing bolt with demanded effort (108 H•м).
2. Establish a back fixing collar and tighten bolts of its fastening with effort 90 H•м.
3. Fill a finger of a spherical support in assemblage of a rotary fist. Screw a new nut and tighten it with effort 60 ч 72 H•м.
4. Fix on assemblage of the lever a rack of the stabilizer of cross-section stability.
5. Lower the car on the earth and definitively tighten fixture with demanded effort.
6. Establish a wheel.