Mitsubishi Galant

1. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
2. Remove a brake drum/disk (the Brake system see the Head).
3. Remove assemblage of a nave with the wheel bearing (see Has undressed Removal and installation ступичных assemblages).
4. Prop up a jack a beam of the back bridge.
5. Disconnect from the longitudinal lever the bottom support of the shock-absorber.
6. Disconnect the longitudinal lever from a beam of the back bridge.
7. Turn out a through bolt of fastening of the longitudinal lever to кузовному to an element and remove lever assemblage from the car.

1. Get assemblage of the longitudinal lever on the regular place and establish a through bolt of its fastening on a body. Tighten a nut of a bolt with demanded effort (100 ч 120 H•м).
2. Connect the lever to a beam of the back bridge. Tighten a fixing bolt with effort 100 ч 120 H•м.
3. Fix on the lever the bottom support of the shock-absorber, - tighten fixing with effort 80 ч 100 H•м).
4. Clean propping up a beam of the back bridge a jack.
5. Establish into place ступичную assemblage.
6. Establish a brake drum/disk (the Brake system see the Head).
7. Establish a wheel and lower the car on the earth.

1. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
2. Remove a brake drum/disk (the Brake system see the Head).
3. Remove assemblage of a nave with the wheel bearing (see Has undressed Removal and installation ступичных assemblages).
4. Prop up a jack a beam of the back bridge.
5. Disconnect from the longitudinal lever the bottom operating lever of a suspension bracket.
6. Disconnect from the lever the top coupler.
7. Give a through bolt of fastening of the longitudinal lever to кузовному to an element and remove lever assemblage from the car.

1. Get assemblage of the longitudinal lever on the regular place and establish a through bolt of its fastening on a body. Tighten a nut of a bolt with demanded effort (100 ч 120 H•м).
2. Connect to the lever the top coupler, tighten a fixing boat with effort 90 H•м.
3. Connect to the longitudinal lever the bottom operating lever, tighten a fixing bolt with effort 90 H•м.
4. Clean propping up a beam of the back bridge a jack.
5. Establish into place ступичную assemblage.
6. Establish a brake drum/disk (the Brake system see the Head).
7. Establish a wheel and lower the car on the earth.

1. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
2. Prop up a jack a beam of the back bridge.
3. Disconnect the longitudinal lever from a fist ступичной assemblages.
4. Give a through bolt of fastening of the longitudinal lever to кузовному to an element and remove lever assemblage from the car.

1. Get assemblage of the longitudinal lever on the regular place and establish a through bolt of its fastening on a body. Tighten a nut of a bolt with demanded effort (137 ч 157 H•м).
2. Connect the lever to a fist ступичной assemblages, tighten a fixing bolt with effort 118 ч 137 H•м.
3. Clean propping up a beam of the back bridge a jack.
4. Establish a wheel and lower the car on the earth.

1. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
2. Remove a brake drum/disk (the Brake system see the Head).
3. Remove ступичную assemblage (see Has undressed Removal and installation ступичных assemblages).
4. Prop up a jack a beam of the back bridge.
5. Disconnect from the longitudinal lever the bottom support of the shock-absorber.
6. Disconnect from the lever a rack of the stabilizer of cross-section stability.
7. Disconnect from the lever a tip of cross-section draught.
8. Disconnect from the longitudinal lever the bottom operating lever of a suspension bracket.
9. Give a through bolt of fastening of the longitudinal lever to кузовному to an element and remove lever assemblage from the car.

1. Get assemblage of the longitudinal lever on the regular place and establish a through bolt of its fastening on a body. Tighten a nut of a bolt with demanded effort (140 ч 160 H•м).
2. Connect to lever assemblage the bottom operating lever of a suspension bracket, tighten a fixing bolt with demanded effort (140 ч 160 H•м).
3. Connect to the lever a tip of cross-section draught. Tighten a fixing nut with effort 29 H•м.
4. Establish on the lever a rack of the stabilizer of cross-section stability, tighten fixing to a hook with effort 40 H•м.
5. Connect to the lever the shock-absorber. Tighten a fixing bolt with demanded effort (90 H•м).
6. Clean propping up a beam of the back bridge a jack.
7. Establish into place ступичную assemblage.
8. Establish a brake drum/disk.
9. Establish a wheel and lower the car on the earth.