Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal and installation of the top operating levers of a back suspension bracket

Models Galant on 1993 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
3. Prop up a jack the bottom lever of a back suspension bracket.
4. Turn out a coupling bolt of a collar of fastening of a brake line.
5. Give a fixing nut and by means of the special tool of type MB9f35 liberate the top spherical support from the longitudinal lever of a suspension bracket/fist ступичной assemblages, - if the support is subject to further use, operate extremely cautiously.
6. Mark position of the clown of the top adjusting bolt and turn out last from the operating lever.
7. Remove the top lever from the car.


Installation

 PERFORMANCE ORDER

1. Establish the lever on the regular place, screw an adjusting bolt and слега tighten it, having achieved combination of the landing labels put in the course of dismantle.
2. Запрессуйте the top spherical support in шпиндельную assemblage also tighten with demanded effort (72 H•м) a new fixing nut of a spherical finger.
3. Establish a wheel and lower the car on the earth.
4. Definitively tighten with demanded effort (160 H•м) an adjusting bolt of the top lever.
5. Connect a negative wire to the battery.
6. Check up corners of installation of back wheels, in case of need make corresponding updating.


Models Galant 1994 ÷ 1998 вып.

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props. Remove assemblage of a corresponding back wheel.

2. Turn out a through bolt of fastening of the top lever to a fist ступичной assemblages.

3. Turn out bolts of fastening of the top lever to a car body.

4. Remove assemblage of the top lever.
5. In case of need give fixing nuts and take through bolts of fastening of basic arms of the top lever.


Installation

 PERFORMANCE ORDER

1. Establish on assemblage of the top lever basic arms. Tighten nuts of fixing bolts with demanded effort (57 H•м).
2. Establish assemblage of the top lever on the car and tighten four fixing bolts with effort 39 H•м.
3. Establish a through bolt of fastening of the top lever to a fist ступичной assemblages, freely tighten a fixing nut.
4. Establish a wheel and lower the car on the earth.
5. Definitively tighten with demanded effort (98 H•м) a nut of a through bolt.
6. Check up corners of installation of back wheels, in case of need make corresponding updating.


Models Diamante

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
2. Disconnect a bar of the stabilizer of cross-section stability and remove rack-mount assemblage of a suspension bracket.
3. Prop up the longitudinal lever a jack and give самоконтрящуюся a fastening nut to it of the operating lever.
4. By means of a stripper liberate from the longitudinal lever the top spherical support.
5. Disconnect the operating lever from a stretcher and remove it from the car.


Installation

 PERFORMANCE ORDER

1. Establish the operating lever on a stretcher, slightly tighten a fixing bolt.
2. Connect the operating lever to the longitudinal lever and tighten самоконтрящуюся a nut with demanded effort (75 ÷ 89 H•м).
3. Establish rack-mount assemblage and connect a bar of the stabilizer of cross-section stability.
4. Establish a wheel and lower the car on the earth.
5. Definitively tighten a bolt of fastening of the lever to a stretcher with demanded effort (75 ÷ 89 H•м).
6. Check up corners of installation of back wheels, in case of need make corresponding updating.