Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblages of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Removal and installation of the top levers of a forward suspension bracket (model Galant 1994 - 1998 of вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblages of naves from wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblages of a back suspension bracket
   Removal and installation of the top operating levers of a back suspension bracket
   Removal and installation of the bottom operating levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation ступичных assemblages
   Removal and steering wheel installation
   Removal and installation подрулевого the combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism from a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment





Removal and installation of the switch of ignition

Models Mirage and Galant

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Remove the handle отпускания the cowl lock.
3. Remove a knee emphasis.
4. Remove a sleeve of an air line and the panel of furnish of knee level.
5. Remove a steering wheel (see Has undressed Removal and steering wheel installation).
6. Remove the top and bottom section of a casing of a steering column.
7. On models Galant insert a key into the lock of ignition and turn it in position АСС, then the small sharp tool push inside замковой assemblages a lock pin and take the lock cylinder.

On models with АТ on a wall замкового the cylinder the sliding lever of a drive of blocking of a key from which it is necessary to disconnect приводной a cable is established.

8. At a corresponding complete set dismantle the alarm gauge-switch of extraction of the ignition key.
9. Disconnect from the switch of ignition electroconducting. Turn out fixing screws and take assemblage of the switch from замкового the cylinder.


Installation

 PERFORMANCE ORDER

1. On models with АТ take a key and establish on the lock cylinder the sliding lever and connect to it приводной a cable. Grease a cable with greasing and establish the cylinder in a casing замковой assemblages. Check up serviceability of functioning блокиратора.
2. Fill the ignition switch in a back part of a casing замковой assemblages, - track correctness of combination of chinks.
3. Connect electroconducting and establish a clamp.
4. Establish casings of a steering column.
5. Establish a steering wheel and a knee emphasis.
6. Establish the handle отпускания the cowl lock.
7. Connect a negative wire to the battery, activate a pillow of safety and check up serviceability of functioning of the switch of ignition.


Models Diamante

Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Onboard electric equipment see the Head). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Деактивируйте a safety pillow (the Onboard electric equipment see the Head).
3. Remove a steering wheel (see Has undressed Removal and steering wheel installation).
4. Remove the handle отпускания the cowl lock.
5. Remove located on the panel of a knee emphasis under a steering column switches, turn out opened screws and dismantle an emphasis.
6. Remove the top and bottom sections of a casing of a steering column, - try not to break off directing uvulas.
7. If it is required, remove a sleeve of giving of air in a foot well, then accurately disconnect electroconducting from the ignition switch.
8. Turn out fixing screws and liberate the switch from замкового the cylinder.

Installation

 PERFORMANCE ORDER

1. Fill the switch in a casing замковой assemblages, - track correctness of combination of chinks. Screw and tighten fixing screws.
2. Connect to the switch electroconducting.
3. Establish knee having blown and an air line sleeve.
4. Establish a knee emphasis and the panel of switches.
5. Establish the handle отпускания the cowl lock.
6. Establish a steering wheel.
7. Establish casings of a steering column.
8. Connect a negative wire to the battery, activate a pillow of safety and check up serviceability of functioning of the switch of ignition.