Mitsubishi Galant

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props. Remove both back wheels.
3. Prop up the bottom lever of a suspension bracket a jack.
4. Mark adjusting position of the top plate of a screw spring.
5. On models with an active suspension bracket (Active-ECS) release a nut of fastening of an air-line to the top part of a rack. A sealing ring will throw out, - it is subject to replacement without fail. Turn out fixing bolts and remove from the top part of a rack actuation mechanism Active-ECS, - do not forget to disconnect electroconducting.
6. Turn out a bolt of the bottom support of the shock-absorber. Give nuts of fastening of the top plate of the shock-absorber to кузовному to an element.
7. Lower propping up bottom lever a jack, remove a rack and take it from under the car.

1. Fill the top plate of a screw spring on the regular place and establish a rack on the car, - take advantage of a jack.
2. Tighten the top fixing nuts with demanded effort (45 H•м).
3. The bottom bolt tighten with effort 98 H•м.
4. On models with Active-ECS connect е to a rack an air-line, - do not forget to replace a sealing ring. Tighten штуцерную a nut with demanded effort (9 H•м).
5. Establish on a rack actuation mechanism Active-ECS, connect to it electroconducting and fix bolts.
6. Clean a jack, establish wheels and lower the car on the earth.
7. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. Slightly prop up торсионную a beam and the lever, - track, that the jack did not concern a cross-section jet bar.

Between a head of a jack and a bridge beam it is necessary to lay necessarily wooden брусок, get a jack under the central part of a beam.

4. For the purpose of providing of access to the top fixing nuts remove corresponding elements of an upholstery of a luggage space.
5. On models with an active suspension bracket (Active-ECS) mark and disconnect from the top part of the shock-absorber air-lines. At once закупорьте the open ends of tubes and unions in order to avoid hit in dirt system. Try not to admit перекручивания and перегибания tubes. Remove a sealing ring and the plug. Remove actuation mechanism assemblage.
6. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
7. Turn out the bottom fixing bolt and remove rack-mount assemblage from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. Поддомкратьте a beam of the back bridge, achieving hit of fixing hairpins of the top support of the shock-absorber in reception apertures. Fix a rack in the top position.
3. Screw on hairpins fixing nuts and tighten them with demanded effort (40 H•м).
4. Lower the car on the earth and definitively tighten the bottom bolt of fastening of the shock-absorber with demanded effort (100 H•м).
5. On models with an active suspension bracket establish into place components Active-ECS and restore initial connection of air-lines, - do not forget to replace sealing rings. Tighten a counternut with effort 9 H•м. Moisten штуцерный a socket with soap water, start the engine and check up connection on presence of signs of leaks of air. In case of need replace a sealing ring.
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of a luggage space.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. Slightly prop up a jack the longitudinal lever of a suspension bracket.
4. For the purpose of providing of access to the top fixing nuts remove corresponding elements of an upholstery of a luggage space.
5. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
6. Give a bolt of fastening of a basic arm of a brake hose.
7. Turn out the bottom fixing bolt and remove rack-mount assemblage from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. Поддомкратьте the longitudinal lever, achieving hit of fixing hairpins of the top support of the shock-absorber in reception apertures. Fix a rack in the top position.
3. Screw on hairpins fixing nuts and tighten them with demanded effort (40 H•м).
4. Lower the car on the earth and definitively tighten the bottom bolt of fastening of the shock-absorber with demanded effort (90 ч 110 H•м).
5. Establish a basic arm of a brake hose and tighten a bolt of its fastening with demanded effort (17 H•м).
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of a luggage space.

1. Поддомкратьте the car also establish it on props.
2. Slightly prop up a jack the bottom operating lever of a suspension bracket.
3. For the purpose of providing of access to the top fixing nuts delay outside a stopper of a back seat, lift and remove a pillow. Turn out fixing bolts and remove a seat back.

4. Give the top nuts of fastening of the shock-absorber.

5. Turn out the bottom fixing bolt and remove rack-mount assemblage from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. Поддомкратьте a beam of the back bridge, achieving hit of fixing hairpins of the top support of the shock-absorber in reception apertures. Fix a rack in the top position.
3. Screw on hairpins of a nut and tighten them with demanded effort (44 H•м).
4. Lower the car on the earth and definitively tighten the bottom bolt of fastening of the shock-absorber with demanded effort (98 H•м).
5. Establish into place components of a back seat.

1. For the purpose of providing of access to the top fixing nuts remove corresponding elements of an upholstery of a luggage space.
2. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
3. Поддомкратьте the car also establish it on props.
4. Slightly prop up a jack the longitudinal lever of a suspension bracket.
5. Mark adjusting position of the top plate of a spring concerning the chassis, then give fixing nuts.
6. Turn out the bottom fixing bolt and remove rack-mount assemblage from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. Поддомкратьте the longitudinal lever, achieving hit of fixing hairpins of the top support of the shock-absorber in reception apertures. Fix a rack in the top position.
3. Screw on hairpins fixing nuts and tighten them with demanded effort (27 H•м).
4. Lower the car on the earth and definitively tighten the bottom bolt of fastening of the shock-absorber with demanded effort (90 H•м).
5. Establish a basic arm of a brake hose and tighten a bolt of its fastening with demanded effort (17 H•м).
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of a luggage space.