Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
- Coupling and трансмиссионная a line
   Specifications
   Coupling - the general information and check of a condition of components
   Removal, check of a condition and installation of components of assemblage of coupling
   Removal, check of a condition and installation выжимного the bearing and a plug of deenergizing of coupling
   Check of a condition and replacement of the directing bearing
   Adjustment of a pedal of coupling
   Adjustment of a cable of a drive of coupling, removal and installation тросовой assemblages (models Mirage with тросовым a coupling drive)
   Removal and installation of the main cylinder of coupling
   Removal and installation of the executive cylinder of coupling
   Removal of air from a hydraulic path of a drive of deenergizing of coupling
   Removal and installation of power shafts
   Hinges of power shafts - the general information and service
   Condition check трансмиссионной lines
   Removal and installation карданного a shaft
   Replacement карданного the hinge
   Balancing карданного a shaft
   Removal and installation of assemblage of the central bearing карданного a shaft
   Removal and installation of back semiaxes (model AWD Galant on 1993 вып.)
   Removal and installation ступичной pins of a back axis, the wheel bearing and an epiploon
   Replacement of an epiploon of a leading gear wheel of back differential
   Removal and installation картер back differential (model AWD Galant on 1993 вып.)
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation ступичной pins of a back axis, the wheel bearing and an epiploon

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Поддомкратьте the car also establish it on props.
3. Remove a corresponding back wheel.
4. On the models equipped ABS, remove the wheel gauge, - in order to avoid a gauge exit out of operation try not to admit its electric contact to metal elements of a suspension bracket.
5. Remove a support of the back brake mechanism and, not disconnecting a hydraulic line, tie up its wire to suspension bracket elements, remove a brake disk.
6. Turn out bolts of fastening of a semiaxis to a connecting flange, give nuts and remove washers, - for the purpose of providing of access to самоконтрящейся to a nut slightly take the semiaxis end aside.
7. By means of the special tool of type MB9b11-01 block полуось, then give самоконтрящуюся a nut.
8. By means of a stripper with a nozzle (MB9b11-01 and MB9b41-01) liberate a pin of a back axis from assemblage of the longitudinal lever of a suspension bracket.
9. On equipped ABS models remove from a pin a rotor of the wheel gauge (take advantage of the suitable plug and a press).
10. By means of a press remove from a pin the external bearing with a dustproof cover.
11. By means of a stripper liberate from assemblage of the longitudinal lever an epiploon and the internal bearing.
12. Estimate a condition of a connecting flange and an axis pin. Check up a dustproof cover on presence of signs of deformations and other mechanical damages. Attentively examine bearings on presence of traces of an overheat. Defective components replace.


Installation

 PERFORMANCE ORDER

1. Having taken advantage approaching оправкой, plant in assemblage of the longitudinal lever the internal bearing. Trace establish an epiploon (a curve upwards and against the stop in a coat hanger of the internal lever).

In quality оправки for epiploon planting it is possible to take advantage of a face head approaching on the size, or a piece of a pipe of the corresponding diameter. Застукивайте an epiploon gradually and in regular intervals, - take advantage of a hammer with soft the brisk.

2. Against the stop in a coat hanger plant dustproof caps (internal - deepening outside).
3. Grease with universal greasing an internal surface of sealing sponges of an epiploon of the external bearing. Plant the bearing on an axis pin (epiploon sponges to a connecting flange).
4. Запрессуйте into place роток the wheel gauge (a flute towards a flange).
5. Temporarily establish a pin on assemblage of the longitudinal lever. Establish a connecting flange and screw new самоконтрящуюся a nut.
6. Keeping a pin from проворачивания by means of special adaptation MB9b11-01, tighten самоконтрящуюся a nut with demanded effort (220 H•м).
7. Establish new nuts of fastening of a semiaxis, prepare washers, screw and tighten with demanded effort (55 65 H•м) fixing bolts.
8. Establish a brake disk, a support and components of a lay brake (the Brake system see the Head).
9. Establish wheels and lower the car on the earth. Check up adjustment of a lay brake, in case of need make corresponding updating (the Brake system see the Head).
10. Before to start car operation, "pump over" a pedal of a foot brake before hardness occurrence at its squeezing.