Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of position of lateral doors
   Removal, installation and adjustment of position of a cowl
   Removal, installation and adjustment of position of a door of a back (model Хэтчбэк and the Versatile person)
   Removal, installation and adjustment of position of a cover of a luggage space (model the Sedan)
   Removal and installation of door rear-view mirrors
   Replacement of the aerial of a radio receiver
   Removal and installation of forward wings
   Removal and installation of the panel of devices
   Removal and installation of the central console
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of the external handle of a door and elements of a drive of a latch of the lock
   Removal and installation of the cylinder of the lock of a lateral door
   Removal and installation of the cylinder of the lock of a door of a back/cover of a luggage space
   Removal and installation of the handle of a door of a back
   Removal and installation of door glass and regulator стеклоподъемника
   Removal and installation of the electromotor of a drive стеклоподъемника
   Replacement салонного rear-view mirrors
   Removal and installation of seats
   Removal and installation of the electromotor of a drive of a seat
+ Onboard electric equipment




Removal and installation of door glass and regulator стеклоподъемника

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Lower door glass in extreme bottom position.
3. Remove the panel of an internal upholstery and изоляционный the door screen.
4. Hooking edge of a piece of a fabric, cautiously separate from a doorframe tape молдинг.
5. Remove internal stabilizers of glass.
6. On forward doors remove directing ползун.

7. Prop up a glass bottom edge, then turn out two bolts of fastening of glass to a regulator стеклоподъемника, - not propped up glass can fail in a doorframe.

8. Accurately take glass from a doorframe through a window aperture.
9. Turn out bolts of fastening of a regulator.

10. At a corresponding complete set disconnect electroconducting from the drive electromotor стеклоподъемника.
11. Take a regulator through a special window of access in a doorframe.


Installation

 PERFORMANCE ORDER

1. Before installation it is necessary to grease moving elements of a regulator with universal greasing slightly.
2. Establish a regulator on the regular place and by hand tighten fixing bolts.
3. Since the left bottom bolt and moving clockwise, make a definitive tightening of fixture of a regulator.
4. At a corresponding complete set connect electroconducting to приводному to the electromotor.
5. Fill in a doorframe a windowpane and fix it on a regulator.

On models Hatchback the back support first of all is tightened has flown down, on models a sedan - a lobby.

6. Slowly closing a window, check up correctness of an arrangement of glass in a doorframe aperture. In case of need remove a regulator and slightly develop the apertures provided in it under bolts of fastening of glass, - preliminary make sure, that the glass warp is not connected with deformation of elements of a regulator.
7. Establish other components of a doorframe acting in film for the purpose of providing of access.
8. Connect a negative wire to the battery.