Mitsubishi Galant

1990-2001 of release

Repair and car operation

Mitsubishi Galant
+ Identification numbers of the car
+ Controls
- Options and routine maintenance
   The schedule of routine maintenance of cars Mitsubishi Galant/Mirage/Diamante
   The general data on options and adjustments
   Check of levels of liquids
   Check of a condition of tyres and pressure of their rating
   Replacement of impellent oil and the oil filter
   Check, service and gymnastics of the storage battery
   Check of a condition of components of system of cooling
   Check of a condition and replacement of the hoses located in an impellent compartment
   Check of a condition and replacement of brushes of screen wipers
   Rotation of wheels
   Check of a condition of components of a suspension bracket and steering drive
   Greasing of components of the chassis
   Replacement ATF of automatic transmission and differential of the main transfer, check of a condition and filter AT service
   Check of a condition of brake lines
   Check of a condition/service of disk brake mechanisms
   Check of a condition of protective covers of power shafts
   Check and adjustment of backlashes of valves - only Mirage
   Replacement of a filtering element of an air cleaner
   Service of system of cooling
   Replacement of the fuel filter
   Check and replacement of the valve of system of operated ventilation картера (PCV)
   Check of a condition and replacement of spark plugs
   Condition check, adjustment of effort of a tension and replacement приводных belts
   Check of a condition of components of system of release of the fulfilled gases
   Replacement трансмиссионного oils РКПП
   Replacement of greasing of a distributing box - only all-wheel drive Galant
   Replacement of greasing of back differential - only all-wheel drive Galant
   Check of a condition/service of drum-type brake mechanisms
   Check of serviceability of functioning of a lay brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Check of a condition of seat belts
   Check of a condition and replacement of components of system of ignition
   Check/adjustment of installation of a corner of an advancing of ignition
   Check of a condition of components of system of catching of fuel evaporations
   Check of a condition of components of the power supply system
   Check of a condition and replacement of a belt (it) of drive ГРМ
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Replacement of the fuel filter


At service of components of the power supply system it is not necessary to forget, that gasoline is easily flammable liquid in the higher measure. Do not smoke near to a work place, do not come nearer to it with open fire! Immediately collect all traces of the spilt fuel, put the rags impregnated with PETROLEUM PRODUCTS in such place where the probability of its casual ignition is absolutely excluded! Always hold near at hand the class fire extinguisher In! Try not to suppose gasoline hit on open sites of a skin - long contact such is capable to lead to development of cancer diseases. Remember that the path of system of injection of fuel constantly is under superfluous internal pressure which should be without fail dumped prior to the beginning of work (see the Head of the Power supply system and release).

Before removal of the fuel filter it is necessary to dump pressure in the power supply system (see the Head of the Power supply system and release)!

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. The given work should be made at the cold engine (having waited not less than 3 hours after trip end).
3. On the majority of models considered in the present Management the fuel filter is in an impellent compartment of the car and is fixed on its back partition.
4. For the purpose of simplification of access to the filter, remove an air cleaner cover in gathering with an inlet air line (the Section Replacement of a filtering element of an air cleaner see).
5. Wrap up rags subject to undocking штуцерные connections (at отпускании a socket fuel being under residual pressure can start to be sprayed), prepare a stock of old newspapers for gathering of spilt fuel.

6. Having fixed a nut on the filter from проворачивания, the second key ослабьте a hollow bolt штуцерного connections of an inlet fuel line. Disconnect a pressure head line from the filter, remove and will throw out sealing washers, - at assemblage they are subject to replacement without fail.

7. Operating in a similar manner, release накидную a nut штуцерного a socket of a final line from the bottom party of the filter. Disconnect a line.

8. Having weakened two coupling bolts, take the filter from a collar of an arm of fastening of assemblage on a partition. In case of need remove also an arm.

9. Fill the filter in a fixing collar and while only by hand, tighten bolts, - the certain weak point of planting of the filter will facilitate performance of procedure of connection to assemblage of fuel hoses. Track correctness of installation of the filter: the pointer direction should coincide with a direction of a stream of fuel in a power supply system path.
10. Connect to a fuel line to the bottom party of the filter (do not forget to replace a sealing washer), screw and tighten by hand накидную штуцерную a nut.
11. Bring a pressure head line to the top party of assemblage, screw a hollow bolt штуцерного a socket and tighten it with demanded effort (30 Nanometers), keeping the filter from проворачивания the second key. Tighten накидную a nut of the bottom socket with effort of 35 Nanometers (again keep assemblage from проворачивания the second key).
12. Tighten coupling bolts of a fixing collar with effort of 14 Nanometers.
13. Connect a negative wire to the battery. Having included ignition, lift pressure in a fuel path and check up power supply system components on presence of signs of development of leaks.