Mitsubishi Galant

1 — the Ware box
2 — a loudspeaker Lattice
3 — the Forward overlay of a door threshold (model with a right-hand steering)
4 — the Knee emphasis (models with a right-hand steering)
5 — the Assembly frame of a ware box
6 — Knee (models without a back heater) / line (models with a back heater) an air line
7 — an electroconducting Socket приводного the fan motor
8 — the Hose

9 — the Block of management of system of the distributed injection (MPI)
10 — Вентиляторная assemblage
11 — a fan Casing
12 — the Sealing lining
13 — a fastening Nut крыльчатки
14 — Крыльчатка
15 — Приводной the electromotor

1 — Section of the bottom furnish
2 — the Ware box
3 — the Panel of angular furnish

4 — the Assembly frame of a ware box
5 — Resistive assemblage
6 — Assemblage of the fan of a heater with приводным the motor

1 — Resistive assemblage
2 — Assemblage of the fan of a heater with приводным the electromotor
3 — the Panel of devices

4 — the Connecting sleeve (models without К/В)
5 — the Evaporator (models with К/В)
6 — a fan Casing

1 — the Persistent clamp
2 — the Ware box
3 — the Panel of the bottom furnish
4 — the Sleeve of giving of air in foot wells
5 — Sockets of electroconducting of the relay of management MFI and the gauge-switch of illumination of a ware box
6 — the Assembly frame of a ware box
7 — the Forward overlay of a door threshold
8 — the engine management Module
9 — evaporator Fixture (models with К/В)/clamps of fastening of an air line (model without К/В)

10 — the Hose
11 — Assemblage of the fan with a casing
12 — Приводной the electromotor
13 — the Sealing lining
14 — a fastening Nut крыльчатки
15 — Крыльчатка
16 — Assemblage of the fan with приводным the motor
17 — a fan Casing

1 — the Panel of the bottom furnish
2 — Resistive assemblage
3 — ECM compressor K/V (model with К/В)
4 — Assemblage of the fan of a heater
5 — the Panel of devices

6 — the Clamp
7 — the Connecting sleeve (models without К/В)
8 — evaporator Fixture (models with К/В)
9 — a fan Casing

1 — the Panel of the bottom furnish
2 — the Sleeve of giving of air in foot wells
3 — the Assembly frame of a ware box
4 — evaporator Fixture
5 — Assemblage of the motor of switching of a mode of circulation
6 — the Relay of management MFI

7 — the Block of management MFI
8 — the Right bottom arm of the panel of devices
9 — Assemblage of the fan of a heater with a casing
10 — Assemblage of the fan of a heater
11 — a fan Casing

1 — the blocking Controller приводного belt К/В
2 — Assemblage of the fan of a heater

3 — the Relay of a high-speed mode of functioning of the fan of a heater

Cars considered in the present Management are equipped by system of the additional safety SRS more known as a pillow of safety. Before to perform any works near to assemblage of a pillow or a steering column, without fail disconnect system in order to avoid reception of traumas as a result of its casual operation, - disconnect from the battery at first negative, then for a positive wire and wait not less than two minutes before to start service of the components located near to gauges of directed overloads (the Onboard electric equipment see the Head). Isolation and contact sockets of electroconducting of chain SRS are painted in bright yellow colour. It is not necessary to connect any diagnostic devices to the given chain!

 PERFORMANCE ORDER