Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
- Cooling and heating systems
   Specifications
   Antifreeze - the general data
   Check of serviceability of functioning and the thermostat
   Check of a condition of the fan of system of cooling
   Removal and installation of a radiator of system of cooling
   Check of a condition of the water pump
   Removal and installation of the water pump
   Check of serviceability of functioning and replacement of the block of the gauge of a measuring instrument of temperature of a cooling liquid
   Replacement of the electromotor of a drive of the fan of a heater
   Removal and installation of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Removal and installation of assemblage of the control panel by functioning of a heater and air conditioner, adjustment приводных cables
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Check of serviceability of functioning and replacement of the block of the gauge of a measuring instrument of temperature of a cooling liquid

Start procedure performance only after full cooling of the engine! Preventions in the beginning see also Has undressed Antifreeze - the general data. Remember that at the included ignition the fan of system of cooling can work even at the muffled engine.


Measuring instrument check

 PERFORMANCE ORDER

1. Disconnect electroconducting from the block of the gauge of a measuring instrument.

2. Connect a suitable lamp-sampler (12 В/3.4 Вт) between a socket of the gauge from a plait of electroconducting and weight.
3. Include ignition.
4. If all components function regularly, the lamp-sampler should light up, and the arrow of a measuring instrument of temperature - to deviate. If the lamp works regularly, but the arrow does not move, replace a measuring instrument (the Onboard electric equipment see the Head), preliminary having checked up a condition of a corresponding safety lock and electroconducting. If to ignition inclusion do not react neither a lamp, nor a measuring instrument, check up a condition of corresponding electroconducting, make necessary regenerative repair, replace the failed components.


Gauge check

 PERFORMANCE ORDER

1. Merge cooling liquid from the engine block, having lowered its level below level of an arrangement of the gauge.
2. Disconnect electroconducting and remove the gauge block.

3. Lower a working tip of the gauge in a vessel with hot water, having fixed temperature of last by means of the thermometer.

4. By means of an ohmmeter measure resistance between plugs of a socket of the gauge lowered in water.
5. Compare result of measurement to requirements of Specifications (the rating value should not fall outside the limits a range 2.21 ÷ 2.69 clod for temperature 20°С, 264 ÷ 328 Ohm for temperature 70°С and 90.5 ÷ 117.5 Ohm for temperature 80°С).
6. The faulty gauge is subject to replacement.


Replacement

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Get under a radiator of system of cooling drain capacity approaching on volume.
3. Merge cooling liquid, having lowered its level below level of an arrangement of the gauge.

4. Disconnect from the gauge electroconducting and turn out it from a casing of the thermostat by means of a deep face head.

5. Screw to the place of the removed gauge new which carving preliminary grease with current-carrying hermetic (not a teflon tape or tape ФУМ). Tighten the gauge with demanded effort (10 ÷ 12 H•м).

6. Connect electroconducting.
7. Fill system of cooling and make sure of serviceability of functioning of a measuring instrument of temperature (see above).