Mitsubishi Galant

1990-2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
- The engine
   - Removal/installation of the power unit, dismantle of components
      The general information
      Removal and engine installation
      Removal and installation of a cover of a head of cylinders
      Removal and installation of assemblages of a drive of valves
      Removal and thermostat installation
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and installation турбокомпрессора
      Removal and installation of a radiator of system of cooling (all models)
      Removal and installation of the fan of system of cooling of the engine
      Removal and installation of the water pump
      Removal and installation of a head of cylinders
      Removal and pallet installation картера the engine
      Removal and installation of the oil pump
      Removal and installation демпфера крутильных fluctuations of a cranked shaft
      Removal and installation of a cover of drive ГРМ and газораспределительного a belt
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of a drive of valves, check of a condition of components
      Removal and installation of a balancing shaft
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of a flywheel/privodnogo of a disk
   + Regenerative repair of the engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and installation демпфера крутильных fluctuations of a cranked shaft

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Throw off from a pulley of a cranked shaft belts of a drive of auxiliary units (see the Head of Adjustment and routine maintenance).
3. Поддомкратьте the car also establish it on props.
4. Remove the right forward wheel (from the passenger party of the car).

5. For the purpose of providing of access to демпферу крутильных fluctuations remove локер protection of a wheel arch.

6. On l models 1.5, 1.6 l, 2.0 l and 2.4 l turn out bolts of fastening of a pulley to a cogwheel of a cranked shaft. On l models 1.5, 1.8 l, 3.0 l and 3.5 l turn out the central bolt of fastening of a pulley of a cranked shaft.

7. By means of a stripper dismantle демпфер крутильных fluctuations from a shaft pin.


Installation

 PERFORMANCE ORDER

1. Having tracked hit шпонки in a reciprocal groove, plant демпфер крутильных fluctuations on a pin of a cranked shaft,
2. On l models 1.5, 1.8 l, 3.0 l and 3.5 l screw the central bolt of fastening of a pulley and tighten it with demanded effort (70 ÷ 100 H•м - for l models 1.5, 185 H•м - for models 1.8 of l both 3.5 l and 150 ÷ 160 H•м - for models 3.0).
3. On l models 1.5, 1.6 l, 2.0 l and 3.5 l screw bolts of fastening of a pulley to a shaft cogwheel. Tighten fixture with demanded effort (14 H•м - for l models 1.5, 20 ÷ 30 H•м - for models 1.6 both 2.0 l and 25 H•м - for models 2.4).
4. Establish into place локер protection of a wheel arch.
5. Establish a wheel, lower the car on the earth and tighten wheel nuts.
6. Establish belts of a drive of auxiliary units (see the Head of Adjustment and routine maintenance).
7. Connect a negative wire to the battery.