Mitsubishi Galant

1990-2001 of release

Repair and car operation


Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
- The power supply system and release
   Specifications
   Сбрасывание pressure in the power supply system
   Removal and installation of the case of a throttle
   Removal and installation of a fuel highway and injection injectors
   Check of a condition and replacement of fuel lines and them штуцерных connections
   Check of serviceability of functioning of injectors
   Removal and installation of a regulator of pressure of fuel
   Removal and installation of a safety valve of a fuel tank
   Removal and installation of a fuel tank
   Cleaning and repair of a fuel tank - the general data
   Check of serviceability of functioning of the fuel pump, measurement of pressure of fuel
   Removal and installation of the fuel pump/gauge of the expense of fuel
   Removal and installation of assemblage of an air cleaner
   Release system
+ Engine electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and installation of the case of a throttle

Details of installation of the case of a throttle on l models 1.5

1 — a gas Cable
2 — the Socket of electroconducting TPS
3 — the Socket of electroconducting of the servo-driver of management of idling turns
4 — Vacuum hoses

5 — Hoses of a water path
6 — the throttle Case
7 — the Sealing lining


Details of installation of the case of a throttle on l models 1.8

1 — a gas Cable
2 — the Socket of electroconducting TPS
3 — the Socket of electroconducting of the servo-driver of management of idling turns
4 — Vacuum hoses

5 — the Vacuum hose (models with темпостатом)
6 — Hoses of a water path
7 — the throttle Case
8 — the Sealing lining


Details of installation of the case of a throttle on models 1.6 of l and 2.0 l DOHC

1 — a gas Cable
2 — the Ventilating hose
3 — the Inlet air line
4 — the Air sleeve With
5 — the Vacuum hose
6 — electroconducting Sockets приводного motor IAC and the gauge-switch of the closed position throttle заслонки
7 — the Socket of electroconducting TPS
8 — the Transit hose of a water path

9 — Перепускной a hose of a water path
10 — the Screw of fastening of a plate of grounding
11 — the Basic arm of the case of a throttle and a grounding plate
12 — the Branch pipe of connection of an air line
13 — the Sealing lining
14 — the throttle Case
15 — the Sealing lining


Details of installation of the case of a throttle on models 3.0 of l SOHC and DOHC

1 — a gas Cable
2 — the Socket of electroconducting TPS
3 — the Socket of electroconducting of the servo-driver of management of idling turns (I — AC)
4 — Vacuum hoses

5 — the Hose of a water path
6 — the Vacuum tube
7 — the throttle Case
8 — the Sealing lining


Details of installation of the case of a throttle on l models 3.5

1 — a gas Cable
2 — the Inlet air line
3 — Hoses of a heating path
4 — the Vacuum hose
5 — the Socket of electroconducting TPS

6 — the Socket of electroconducting of the servo-driver of management of idling turns
7 — the throttle Case
8 — the Sealing lining


Removal

 PERFORMANCE ORDER

1. Details of installation of the case of a throttle on various engines are presented on illustrations.
2. Dump pressure in the power supply system (Section Сбрасывание of pressure in the power supply system see).
3. Empty cooling system.

4. Mark position of an adjusting bolt on a fixing flange of a cable of a drive throttle заслонки (gas). Turn out a bolt and disconnect a cable from the lever of a drive throttle заслонки on the throttle case. Take a cable aside.

5. Disconnect from the case of a throttle and take aside a ventilating hose and a hose of giving of air.
6. Mark and disconnect vacuum hoses.

7. Mark and disconnect brought to the case of a throttle electroconducting.

8. Disconnect from the basis of the case of a throttle transit and перепускной hoses of a water path.
9. At a corresponding complete set disconnect the tyre of grounding and remove from the engine a basic arm of the case of a throttle and a grounding plate.
10. Remove a branch pipe of connection of an air line its sealing lining.

11. Turn out fixing screws and remove the case of a throttle from the engine. Remove a sealing lining, - at installation it is subject to replacement without fail.


Installation

 PERFORMANCE ORDER

1. Carefully smooth out all interfaced surfaces, lay on the delivery chamber of the inlet pipeline a new sealing lining.
2. Establish the throttle case. Screw and tighten with demanded effort fixing bolts.
3. Having replaced a sealing lining, establish a branch pipe of connection of an inlet air line.
4. At a corresponding complete set establish a basic arm and a grounding plate. Screw fixing bolts and tighten them with demanded effort (15 ÷ 22 H•м).
5. Screw the screw of fastening of a plate of grounding.
6. Connect to the case of a throttle hoses of a water path and fix their new collars.
7. Watching conformity the marks put in the course of dismantle, restore initial connection of vacuum hoses and electroconducting.
8. Connect a gas cable, having screwed in former position an adjusting bolt. Check up correctness of adjustment of a cable.
9. Connect an inlet air line and a ventilating hose.
10. If removed, establish into place the battery and connect to it wires (at first positive, then - negative).
11. Fill in in the engine a fresh cooling liquid (see the Head of Adjustment and routine maintenance).