Mitsubishi Galant

1990-2001 of release

Repair and car operation

Mitsubishi Galant
+ Identification numbers of the car
+ Controls
+ Options and routine maintenance
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
- Control systems of the engine
   Specifications
   System of operated ventilation картера (PCV) - the general information, check of a condition and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a condition and replacement of components
   System рециркуляции the fulfilled gases (EGR) - the general information, check of a condition and replacement of components
   System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions
   Replacement of the module of management (ЕСМ/PCM)
   Information gauges and actuation mechanisms - the general information, check of serviceability of functioning, removal and installation
   The Katalitichesky converter - the general information, check of a condition and replacement
+ Manual transmission
+ Coupling and transmission a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Mobile Mechanic

System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions

Data on diagnostic devices

Check of serviceability of functioning of components of systems of injection and decrease in toxicity of the fulfilled gases is made by means of a universal digital measuring instrument (multimeter). Use of a digital measuring instrument preferably for the several reasons. First, on analogue devices it is difficult enough (at times, it is impossible), to define result of the indication to within the 100-th and thousand shares while at inspection of the contours including in the structure electronic components, such accuracy gets special value. The second, the reason that fact is not less important, that the internal contour of a digital multimeter, has high enough impedance (internal resistance of the device makes an order of 10 million Ohm). As the voltmeter is connected to a checked chain in parallel, accuracy of measurement by that above, than the smaller parasitic current will pass through actually device. The given factor is not essential at measurement concerning high values of pressure (9 ч 12), however there is defining at diagnostics of elements giving out low-voltage signals, such, as, for example, an oxygen gauge where it is a question of measurement of shares of volt.

The most convenient devices for diagnostics of control systems by the engine of modern models of cars are manual input readers сканерного type. Scanners of the first generation serve for reading of codes of malfunctions of systems OBD-I. Before application the input reader should be checked up on conformity of model and year of release of the checked car. Some scanners are multipurpose, at the expense of possibility of change of a cartridge depending on model of the diagnosed car (Ford, GM, Chrysler, etc.), others are adhered to requirements of the regional authorities and intended for use in certain areas of the world (Europe, Asia, the USA etc.), see more low more in detail.

With introduction in manufacture meeting the requirements of last legislations on preservation of the environment of system of onboard diagnostics of the second generation (OBD-II) input readers of a special design have started to be issued. Some manufacturers have adjusted release of the scanners intended for use by mechanics-fans in house conditions, - ask in shops of automobile accessories.

In spite of the fact that reading of codes of malfunctions in systems OBD II is not obviously possible without use of the special scanner, more low in the present Chapter the description of some elementary checks of separate components of system is resulted.

Parallel supervision of parametres of signals, resistance and pressure in all chains of management is possible by means of a splitter included consistently in a socket of the block of engine management. Thus on the switched off, working engine or during car movement, measurement of parametres of signals on splitter plugs from what the conclusion about possible defects becomes is made.

For diagnostics of electronic systems of the engine, automatic transmission, ABS, SRS special diagnostic scanners (Pointer) or testers (Retriever) with a certain cartridge (if are provided), a universal cable and a socket are applied. Besides, it is possible to apply the expensive specialised automobile diagnostic computer specially developed for full diagnostics of the majority of systems of modern cars to this purpose (for example, ADC2000 firms Launch HiTech, or ESA 560, FSA, BEA firms BOSH), or the usual computer with a special cable and the program browser ОВD II.

Some scanners, besides usual operations of diagnostics, allow, at connection with the personal computer to unpack stored in memory of the block of management basic schemes элетрооборудования (if are put in pawn), to program anticreeping system, to observe signals in car chains in real time.

The free version of browser OBD II for diagnostics of your car, you can download from our site: arus. spb. ru

Basically, reading written down in memory of system of self-diagnostics of codes of malfunctions on some cars can be made also on a control lamp of refusals (MIL) / ”Check up the engine” on a control panel.

The scanner only reads out the malfunctions brought memory and clears memory of malfunctions. Besides the scanner supports only report ISO. The tester in addition can make active and show current data and supports reports SAE and ISO.

All cartridges for a tester can be used and in the scanner. Thus functions will be limited only by reading and memory clearing.

Firm ToolRama Inc devices can be applied to diagnostics, for example. (3500 NW Boca Raton Blvd., Boca Raton, Florida, 33431, USA 1 877 866 5726 - 561 750 4511 - 561 338 8447 FAX):

· Tester R000 or scanner P000
With cartridges Т044 or Т054,
· Universal cable N000, Socket N04А;
· Multiplexer N002A.

With devices offered by firm "BOSСH", you can get acquainted on a site: www.bosсh.de.

For the majority of cars of release since 1996 supporting report SAE/ISO 9141 OBD II cartridge OBD II carrying out following functions can be used:

· Reading and removal of codes of malfunctions OBD II. Reflexion of results of tests of the gauge of oxygen.
· the Continuous control of systems of ignition, injection and components.
· Reflection of the list of the current given and fixed unstable refusals:

a) Absolute pressure in the inlet pipeline;
b) Pressure of the gauge of oxygen;
c) Temperature of a cooling liquid of the engine;
d) Settlement loading of the engine;
e) Speed of the car;
f) Quality of fuel;
g) air Expense (on weight);
h) an ignition Advancing;
i) Position throttle заслонки;
j) Temperature of soaked up air.

In addition to codes of malfunctions "P0", the device also reflects the expanded codes "P1" for models Acura, Audi, BMW, Chrysler, Dodge, FORD, Geo, GM, Honda, Hyundai, Infinity, Kia, Lexus, Lincoln, Mercury, Mazda, Mercedes, Mitsubishi, Nissan, Porsche, Saturn, Seat, Skoda, Subaru, Suzuki, Toyota, Volvo, VW.

Features of specialised automobile diagnostic device ADC2000:

· the Built in 4-channel oscilloscope with standard preset for 19 gauges.
· the Analyzer of system of ignition for check primary and secondary chains (with pressure to 100 кВ) on systems with the distributor or separate coils of ignition - with the control of time of burning, peak value of pressure, a corner of an advancing of ignition, a current, and turns.
· the Two-channel multimeter with digital and graphic data presentation on pressure (150В), frequency (1100 кГц), a current (150А).
· the Built in scanner for the basic systems on cars: VAG, MB, BMW, Volvo, Toyota/Lexus, Mitsubishi, Nissan, Honda, Mazda, GM, Ford, Chrysler, Daewoo, Hyundai, Kia, Samsung, and also on cars supporting report OBD-II.
· cartridges are not required – you can execute updating of programs of the device, having downloaded necessary updatings xчерез Internet.
· the Software for communication with the personal computer.

The information on use of these devices contains in applied documents. About devices you can get acquainted with details on sites www.programatools.com, www.bosh.de and www.lasn.com.

For diagnostics carrying out we recommend to you to address for the qualified help of experts HUNDRED.

Contacts of a diagnostic socket for used reports:

ISO 9141-2 (Chrysler, European and the majority of the Asian models) Contacts 4, 5, 7, 15, 16
SAE J1850 PWM (American Ford) Contacts 2, 4, 5, 10, 16
SAE J1850 VPW (General Motors) Contacts 2, 4, 5, 16 (without 10)

Report ISO 9141-2 is identified by presence of contact 7 and absence of contacts 2 and-or 10 on a diagnostic socket.

Reports SAE J1850 VPW (Variable Pulse Width Modulation) or SAE J1850 PWM (Pulse Width Modulation) are identified by absence of contact 7.

All three reports of data exchange work through standard cable OBD-II with socket J1962.

№ a conclusion	Appointment
1	It is set by the manufacturer
2	Line Bus +, SAE J1850
3	It is set by the manufacturer
4	Connection with the case
5	The case - an alarm conclusion
6	It is set by the manufacturer (CAN high level, J-2284)
7	Line K, ISO 9141
8	It is set by the manufacturer
9	It is set by the manufacturer
10	Line Bus – SAE J1850
11	It is set by the manufacturer
12	It is set by the manufacturer
13	It is set by the manufacturer
14	It is set by the manufacturer (CAN Low level, J-2284)
15	Line L, ISO 9141
16	Battery plus through a safety lock. Energised at any position of the lock of ignition

The scheme of an arrangement of components of engine management on l models 1.5.

And — the Gauge-switch of the permission of start (model with АТ)
In — the ignition Distributor (with built in gauge CMP, the coil and the key transistor)
With — Gauge ECT
D — the Socket of adjustment of a corner of an advancing of ignition
Е — the Control plug of the fuel pump
F — system IAC Electromotor
G TPS — (with the built in gauge-switch of the closed position throttle заслонки)
Н — Gauge MAP
I — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
J — Electromagnetic valve EGR
To — Gauge IAT
L — the Gauge-switch of pressure of system of hydrostrengthening of a wheel (ГУР)
M — Gauge CKP
N — the Relay of coupling of compressor K/V

About — the Injector
Р — Diagnostic socket DLC
Q — the Control lamp of refusals / ”Check up the engine”
R — VSS (язычковый the gauge-switch)
S — Switch K/V
Т — Relay MFI
U — the engine management Module (ECM)
V — the Warmed up oxygen gauge (back)
W — the Warmed up oxygen gauge (forward)

The scheme of an arrangement of components of a control system on l models 1.6

And — the Gauge of measurement of an air stream (with the built in gauges of temperature and atmospheric pressure)
In — Gauge ECT
WITH — TPS
D — the Gauge-switch of position of idling
Е — the Gauge of a corner of turn of a cranked shaft/vmt
F — the Oxygen gauge
G — VSS (язычковый the gauge-switch)
Н — Switch K/V
I — the Gauge-switch of pressure ГУР
J — the Gauge of temperature EGR (the Californian models)
To — the Injector
L — the Step-by-step motor of system of stabilisation of turns of idling
M — the ignition Coil (the key transistor)

N — the Relay of management MPI
About — Relay K/V
Р — the Electromagnetic valve of a purge of an adsorber
Q — Electromagnetic valve EGR (the Californian models)
R — the Plug of adjustment of a corner of an advancing of ignition
S — the self-diagnostics Plug
Т — the Control plug of the fuel pump
U — the engine management Block
V — the Gauge-switch of the permission of start (АТ)

The scheme of an arrangement of components of a control system of the engine/decrease of toxicity of the fulfilled gases on l models 1.8

1 — Gauge MAF (with built in gauge IAT)
2 — Gauge ECT
3 — Gauge CMP
4 — Valve EGR
5 — Valve IAC (from below on the throttle case)

6 — TPS
7 — Gauge MAP
8 — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
9 — Valve PCV
10 — the Electromagnetic valve of management EGR

The scheme of an arrangement of components of a control system of the engine on l models 2.0 (SOHC)

And — the Oxygen gauge
In — the Gauge of measurement of an air stream (under the volume expense) (with built in gauges IAT and atmospheric pressure)
With — the Electromotor of system of stabilisation of turns of idling (the gauge-switch of the closed position throttle заслонки, the gauge of position of the electromotor)
D — TPS
Е — Gauge ECT
F — the ignition Coil / the key transistor
G — Gauge CKP/CMP
Н — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
I — the Injector
J — the Relay of coupling of compressor K/V
To — Electromagnetic valve EGR (the Californian models)
L — the Gauge of temperature EGR (the Californian models)

M — the Gauge-switch of the permission of start of the engine (АТ)
N — Relay MFI
About — Switch K/V
Р — VSS (язычковый the gauge-switch)
Q — the engine management Module (ECM)
R — the Plug of adjustment of a corner of an advancing of ignition
S — Diagnostic socket DLC
Т — the Control plug of the fuel pump
U — the Gauge-switch of pressure ГУР

The scheme of an arrangement of components of a control system of the engine on l models 2.0 (DOHC)

And — the Warmed up oxygen gauge
In — the Gauge of measurement of an air stream (under the volume expense) (with built in gauges IAT and atmospheric pressure)
With — the Step-by-step electromotor of system of stabilisation of turns of idling
D — TPS
Е — the Gauge-switch of the closed position throttle заслонки (fixed SAS)
F — Gauge ECT
G — the ignition Coil / the key transistor
Н — Gauge CKP/CMP
I — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
J — the Injector
To — the Relay of coupling of compressor K/V
L — Electromagnetic valve EGR

M — the Gauge of temperature EGR
N — Relay MFI
About — Switch K/V
Р — VSS (язычковый the gauge-switch)
Q — the engine management Module (ECM)
R — the Plug of adjustment of a corner of an advancing of ignition
S — Diagnostic socket DLC
Т — the Control plug of the fuel pump
U — the Gauge-switch of pressure ГУР
V — the Gauge-switch of the permission of start of the engine (АТ)

The scheme of an arrangement of components of a control system of the engine/decrease of toxicity of the fulfilled gases on l models 2.4

1 — Gauge CKP
2 — Valve PCV
3 — Gauge MAP
4 — Electromagnetic valve EGR
5 — TPS
6 — Valve EGR (from below on the throttle case)

7 — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
8 — Gauge MAF (with built in gauge IAT)
9 — Valve IAC (from below on the throttle case)
10 — Gauge CMP (in the ignition distributor)
11 — Gauge ECT
12 — the Coal adsorber of system EVAP (under a mudguard of a wheel arch)

The scheme of an arrangement of components of a control system of the engine on l models 3.0 (SOHC)

And — the Gauge of measurement of an air stream (under the volume expense) (with built in gauges IAT and atmospheric pressure)
In — the Step-by-step electromotor of system of stabilisation of turns of idling
With — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
D — TPS (with the built in gauge-switch of the closed position throttle заслонки)
Е — the Gauge of temperature EGR (all Californian models and federal models since 1995 вып.)
F — Electromagnetic valve EGR (all Californian models and federal models since 1995 вып.)
G — the Warmed up oxygen gauge
Н — the Plug of adjustment of a corner of an advancing of ignition
I — the detonation Gauge
J — the Electromotor variable induction подмешивания (DC-motor) (with the built in gauge of position of the operating valve)
To — the ignition Coil / the key transistor
L — Gauge CKP/CMP

M — the Gauge-switch of pressure ГУР
N — the Injector
About — Gauge ECT
Р — the Relay of coupling of compressor K/V
Q — the Gauge-switch of the permission of start of the engine (АТ)
R — the Control lamp of refusals / ”Check up the engine”; VSS (язычковый the gauge-switch)
S — Switch K/V
Т — the engine management Module (ECM)
U — the Diagnostic socket

The scheme of an arrangement of components of a control system of the engine on l models 3.0 (DOHC)

And — the Gauge of measurement of an air stream (under the volume expense) (with built in gauges IAT and atmospheric pressure)
In — the Step-by-step electromotor of system of stabilisation of turns of idling
With — the Gauge of position of a pedal of gas (with the built in gauge-switch of the closed position throttle заслонки) (equipped темпостатом models)
D — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
Е — TPS (equipped темпостатом models)
F — the Gauge of temperature EGR
G — Electromagnetic valve EGR (the Californian models)
Н — the Plug of adjustment of a corner of an advancing of ignition
I — the detonation Gauge
J — the Warmed up oxygen gauge
To — the Electromotor variable induction подмешивания (DC-motor) (with the built in gauge of position of the operating valve)
L — the Gauge-switch of pressure ГУР
M — Gauge CMP
N — the Injector

About — Gauge ECT
Р — Gauge CKP
Q — the ignition Coil / the key transistor
R — the Relay of coupling of compressor K/V
S — the Gauge-switch of the permission of start of the engine (АТ)
Т — Gauge VSS (язычковый the gauge-switch)
U — Switch K/V
V — the engine management Module (ECM)
W — the Diagnostic socket

The scheme of an arrangement of components of a control system of the engine on l models 3.5

And — the Gauge-switch of pressure ГУР
In — the Warmed up oxygen gauge (forward)
With — the Warmed up oxygen gauge (back)
D — the Electromagnetic valve of a purge of a coal adsorber of system EVAP
Е — Electromagnetic valve EGR
F — the Differential gauge of pressure in the pipeline
G — TPS (with the built in gauge-switch of the closed position throttle заслонки)
Н — Step-by-step electromotor IAC
I — Gauge CMP
J — the Control plug of the fuel pump
To — the Gauge of measurement of an air stream (under the volume expense) (with built in gauges IAT and atmospheric pressure)
L — the Relay of coupling of compressor K/V
M — Gauge CKP

N — the Injector
About — Gauge ECT
Р — VSS
Q — the Gauge-switch of the permission of start of the engine (АТ)
R — the ignition Coil / the key transistor
S — the Control lamp of refusals / ”Check up the engine”
Т — Switch K/V
U — Diagnostic socket DLC
V — Relay MfI/toplivnogo / the fuel pump
W — ECM

The scheme of an arrangement of components of a control system of the engine on models Galant of 1999-2000 3.0 l (SOHC)

And — Gauge CKP
In — Electromagnetic valve EGR
With — the Warmed up oxygen gauge of the right number of cylinders (forward) (the Californian models)
D — the detonation Gauge
Е — the Warmed up oxygen gauge of the right number of cylinders (back) (the Californian models)
F — the Differential gauge of pressure in the pipeline
G — the Injector
Н — TPS
I — Step-by-step electromotor IAC
J — the ignition Distributor (with built in gauge CMP and the ignition coil)
To — the Relay of coupling of compressor K/V
L — the Gauge-switch of pressure ГУР
M — the Warmed up oxygen gauge of the left number of cylinders (back) (the Californian models)

N — the Warmed up oxygen gauge of the left number of cylinders (forward) (the Californian models)
About — the fan Controller
Р — VSS
Q — Gauge ECT
R — the Gauge-switch of the permission of start of the engine (АТ)
S — the Gauge of measurement of an air stream (under the volume expense) (with built in gauges IAT and atmospheric pressure)
Т — Diagnostic socket DLC
U — PCM
V — the Differential gauge of pressure in a fuel tank
W — the Forward warmed up oxygen gauge (federal models)
Х — the Back warmed up oxygen gauge (federal models)

The general information and safety measures

Electronic systems of injection and decrease in toxicity of the fulfilled gases in the course of the functioning at car operation co-operate with the various other systems which are responsible for efficiency of return of the engine. All listed systems include in the structure a set of information gauges and the electronic module of management (ЕСМ/PCM).

Similar sort of system it is possible to compare on the structure to the central nervous system of a human body where the brain role plays the electronic module of management, and as the nervous terminations information gauges act. Gauges send signals on PCM which analyzes the arriving information and develops reciprocal commands on updating of corresponding working parametres.

Let's consider the specific example allowing more clearly to imagine a principle of functioning of system: built in in release system the oxygen gauge continuously traces level of maintenance О2 in a stream of the fulfilled gases of the engine. If percentage of oxygen considerably deviates some entered into memory of system of control value, PCM immediately receives the corresponding information and on the basis of its analysis develops a corresponding command on updating of duration of opening of injectors of injection of fuel, carrying out thereby adjustment of structure of an air-fuel mix. Duration of the described procedural cycle makes shares of second that provides high reactance of functioning of system. As a result, efficiency of return of the engine is constantly supported at the greatest possible level.

In order to avoid failure of the electronic module of management (ECM/PCM) before to disconnect from it electroconducting without fail switch off ignition and disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

For simplification of introduction щупов a tester in contact socket ECM/PCM at check of entrance/target signals of the last from a socket the holder follows клеммный.

Making a detachment/connection of electroconducting of the module of management try not to bend and not to break off contact plugs.

At measurement of pressure of a food functioning under control of PCM components at all do not suppose short circuit among themselves tester plugs, - short circuit in chain PCM can lead to an irreversible exit of the last out of operation.

System of onboard self-diagnostics of first generation OBD-I

The general information

It is not necessary to be mistaken, assuming, the system consisting of set of various information gauges and operated the electronic processor hardly gives in to diagnostics. All refusals and infringements of functioning of components of system are fixed in electronic memory of the module of management in the form of special digital codes. Reading of codes can be made by connection to diagnostic socket DLC of the special scanner or the digital voltmeter (the first subsection of the present Section see).

The driver is notified on any infringements of functioning of components of systems of injection/decrease of toxicity of the fulfilled gases by means of operation built in in a combination of devices of a control lamp of refusals / ”Check up the engine”. If failure had a temporality and the management module registers system return to normal functioning, the control lamp is disconnected. Moreover, if at operation of a control lamp to switch off ignition after start of the engine the lamp is activated again only in case of repeated registration of refusal by diagnostics system.

For check of serviceability of a condition of a control lamp its short-term operation occurs each time at поворачивании the ignition key in position ON. In the absence of infringements of functioning of control systems by the engine/decrease of toxicity of the fulfilled gases the lamp should go out already later 5 seconds. If at inclusion of ignition of short-term operation of a control lamp does not occur, check up a condition of electroconducting and a safety lock of its electric chain, besides, make sure of integrity of an incandescent filament actually lamps.

Control lamp of refusals / ”Check up the engine” should work also at short circuit on weight of the plug of a socket of updating of a corner of an advancing of ignition.

Remember that codes register refusals of electric contours in aggregate, instead of separate components entering into their structure. So, presence at memory of the module of management of a code № 14 says about malfunction in a chain of the gauge of position throttle заслонки (TPS), that at all unessentially testifies to failure actually the gauge. At revealing of causes of a failure it is necessary to give especially steadfast attention to a condition of corresponding electroconducting and quality of its contact connections. To exclude probability of refusal of a working element of a chain, or to make sure of it it is possible by substitution of obviously serviceable component.

Codes of set of various malfunctions can simultaneously be stored in memory of the processor of system of onboard diagnostics (PCM). Delivery of codes at reading is made in ascending order their identification numbers and does not depend in any way on an order of their entering in memory.

Before to start reading of diagnostic codes, make sure, that pressure developed by the battery corresponds to standard requirements (the engine Electric equipment see the Head).

Remember that at switching-off of electroconducting from the battery or the controller of a control system automatic clearing of memory OBD occurs the engine!

Before input reader connection to diagnostic socket DLC and switching-off it do not forget to turn the ignition key in position OFF. Performance of the given operations at the included ignition can lead to input in memory of the processor of false diagnostic codes (the control lamp of refusals / ”will simultaneously work also Check up the engine”.

Reading of codes of malfunctions by means of the scanner

PERFORMANCE ORDER

The description of procedure of reading of codes from memory ECM by means of the scanner of type Mitsubishi MUT-II is more low resulted. At use of devices of manufacture of other manufacturers strictly adhere to applied instructions!

1. Connect the scanner to located at the left under the panel of devices to diagnostic socket DLC (in case of need preliminary remove an access cover).

On models Galant socket DLC can be in a ware box, to the right of it замковой assemblages.

2. Operating according to instructions of manufacturers consider and write down data given out by the scanner.
3. Make diagnostics of a condition of corresponding elements and their electric contours, execute necessary regenerative repair/replace defective components.
4. Turn a key in position OFF, then again include ignition.
5. Make clearing of memory of the processor of system of onboard diagnostics (see more low).
6. Having repeated reading procedure, make sure of presence at memory OBD of a code of normal functioning of system.

Reading of codes of malfunctions by means of the analogue voltmeter

PERFORMANCE ORDER

1. At a corresponding complete set remove an access cover to socket DLC.

2. Connect the analogue voltmeter between plugs of grounding and target signal OBD of socket DLC.

3. Include ignition.
4. Consider and write down sequence of signals given out by the voltmeter.
5. Make diagnostics of a condition of corresponding elements and their electric contours, execute necessary regenerative repair/replace defective components.
6. Make clearing of memory of the processor of system of onboard diagnostics (see more low).

Clearing of memory of the processor

PERFORMANCE ORDER

At clearing of memory of the processor with input reader application сканерного type follow instructions of manufacturers of the device.

1. Switch off ignition.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! After not less than 1 minutes restore battery connection.

3. Include ignition.
4. Having executed reading procedure, make sure of presence at memory OBD of a code of normal functioning of system.

The list of codes of malfunctions

№ a code	Element in which contour infringement takes place
11	The oxygen gauge
12	The gauge of measurement of an air stream
13	The gauge of temperature of soaked up air (IAT)
14	The gauge of position throttle заслонки
15	The gauge of position of electromotor SC (MPS)
21	The gauge of temperature of a cooling liquid (ECT)
22	The gauge of turns/corners of turn of a cranked shaft
23	The gauge of position of a camshaft (CMP)/VMT the first cylinder
24	The gauge of speed of movement (VSS)
25	The gauge of atmospheric pressure (BARO)
31	The detonation gauge
32	The pressure gauge in the pipeline (MAP)
36	Signal of adjustment of a corner of an advancing of ignition
39	The oxygen gauge (back - models with a turbo-supercharging)
41	Injector
42	The fuel pump
43	EGR (the Californian models)
44	The ignition coil / the key transistor (cylinders №№ 1 and 4) - l models 3.0
52	The ignition coil / the key transistor (cylinders №№ 2 and 5) - l models 3.0
53	The ignition coil / the key transistor (cylinders №№ 3 and 6) - l models 3.0
54	Anticreeping system
55	The position gauge заслонки К/В (or the management activator х.х. [ISC])
59	The warmed up oxygen gauge
61	Cable of the block of management АТ
62	The gauge of position starting заслонки (models without a turbo-supercharging)
64	The generator
71	Vacuum e / the magnetic valve антипробуксовочной systems
72	e / the magnetic ventilating valve антипробуксовочной systems
0	Absence неиспраностей in memory

System of onboard self-diagnostics of second generation OBD-II

The general information

The onboard processor (PCM) is responsible for serviceability of functioning of components of systems of decrease in toxicity of the fulfilled gases, fans of system of cooling, can carry out updatings of a corner of an advancing of ignition and management in working parametres of automatic transmission. Submission to one module of management of power supply systems and ignitions allows to carry out thin adjustments of structure of an air-fuel mix under any conditions of operation of the engine. The general principles of functioning PCM are described in the second subsection of the present Section.

Besides functions of management PCM carries out also constant monitoring of a condition of components of control systems by the engine/decrease of toxicity of the fulfilled gases that does by its central knot of system of onboard self-diagnostics. Codes of electric refusals of various contours of corresponding subsystems and elements register in memory of the processor.

It is necessary to notice, that the system of onboard diagnostics of the second generation is not capable to register the infringements having the mechanical or hydrodynamic nature, however a similar sort refusals can be registered опосредственно at the expense of the influence rendered on functioning of electric knots. So, OBD purely physically it is not capable to reveal such defect as partial infringement of passableness of an injector, nevertheless, the result of the given infringement will be invariably fixed upon pauperisation of an air-fuel mix, indirect registered by the oxygen gauge. Being based on the analysis signals arriving from gauge O2, the module of management of system will carry out record in memory of the processor of a code of a corresponding diagnostic code.

Distinctive feature of systems of self-diagnostics of the second generation (OBD-II) is the organisation in them of the adaptive logic, allowing to make dynamic management of functioning of system of injection of fuel. The given feature allows to compensate automatically deterioration and fluctuations of parametres of components of the power supply system. So, at stably working engine the management module traces the tendency to pauperisation or enrichment of an air-fuel mix and undertakes corresponding steps on updating of its structure, aspiring constantly to maintain стехиометрическое number 14.7:1. Correcting parametres are brought in special memory of the processor, fixed in it and remain accessible at the subsequent cycles of operation of the car (a memory food is carried out directly from the battery and does not depend on position of the lock of ignition).

Reading of codes of malfunctions by means of the scanner

PERFORMANCE ORDER

1 Scanner is connected to located at the left under the panel of devices to a diagnostic socket (DLC).

2. The first step of diagnostics of system always is interrogation of memory of the module of management. At the given stage the general nature of refusals is defined, and consecutive reading of codes allows to elicit the fact of their removal from memory.

3. For reading of codes can be used both the firm scanner of the company-manufacturer of the car, and scanners of foreign manufacturers, - strictly adhere to instructions of manufacturers of the device.

Reading of codes of malfunctions by means of the voltmeter

PERFORMANCE ORDER

1. Find at the left under the panel of devices diagnostic socket DLC.
2. On models since 1996 вып. Switching possibility between arbitration and federal formats of reading of codes is provided. Usually on the models equipped with system of onboard self-diagnostics of the second generation (OBD-II) possibility of reading of codes by throws of pressure ("flashes") on plugs of socket DLC it is not provided also scanner application is an obligatory condition, however, on models Mitsubishi the given possibility is realised.
3. In view of global standardization of codes OBD-II their decoding appreciably becomes simpler. At reading of codes by means of the voltmeter (on pressure throws on plugs DLC) first two positions of a designation are not used. Whereas the car transmission gets to number of components трансмиссионной lines, codes of its refusals also begin with d's letter as coincidence between numbers of codes Mitsubishi and SAE is absent, the figure of a code following a letter also has no value.

4. Codes can be считаны on throws of an arrow of the voltmeter connected to socket DLC. Each code is highlighted by a series from three groups of "flashes". So, to code Р0753 there corresponds group of ”seven flashes” which groups of five and three "flashes" directly follow. Высвечивание the next code begins through a short pause. Duration of all "flashes" is identical, the exception makes only a zero designated by a throw of pressure большей of duration; so code Р0702 (short circuit in chain TPS) will look as follows: seven normal "flashes", one long, then two more normal.

5. Reading of codes is made as follows:

· Make sure of serviceability of a condition of electroconducting and its contact connections;
· Prepare a paper and a pencil for conducting records;
· Find diagnostic socket DLC at the left under the panel of devices of the car;
· Start the engine and make on the car a short trip for system transition in a self-diagnostics mode;
· Park the car, having left the engine working on single turns;
· Connect the voltmeter (analogue or digital) to plugs of diagnostic socket DLC, - a positive wire to the plug 1, negative to the plug 4;
· Watching throws arrows/jumps of indications, consider written down in memory of the processor codes of malfunctions (see more low). Write down results; sometimes probably also reading of codes by flashes of a control lamp “Check up the engine” after short circuit of the plug of 1 socket on the case.
· Make necessary corrections, clear memory of the processor and, having repeated check, make sure of absence in memory of codes.

Clearing of memory of the processor

PERFORMANCE ORDER

1. Clearing of memory of the processor after elimination of malfunctions should is made without fail.
2. For clearing scanner GST or a special tester is used.
3. For clearing of memory ЕСМ connect to system the scanner and in an apportion its menu choose function “CLEARING COEDS” (“Removal of codes”). Further follow the instructions highlighted on the device. Alternatively clearing of memory of system can be made by battery switching-off.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

Battery switching-off also leads to removal of options of the receiver on favourite radio stations.

In order to avoid damage ЕСМ its switching-off and connection should be made only at the switched off ignition!

The list of codes of malfunctions

Codes SAE which is read out by means of the scanner, or by means of the voltmeter or a light-emitting diode (only three younger categories of a code)

P0000	Absence of codes of malfunctions in memory of system
P0100	Infringement in a chain of a measuring instrument of weight of air MAF / the gauge of absolute pressure in the pipeline (MAP)
P0101	Gauge MAF is faulty
P0102	Short circuit on the case or low level of a signal of gauge MAF / MAP
P0103	Short circuit on + or high level of a signal of gauge MAF / MAP
P0104	Alternating error of functioning of gauge MAF
P0105	Malfunctions in a chain of the gauge of absolute pressure (МАР) / the Barometric gauge
P0106	Infringement of functioning of the gauge of absolute pressure (МАР) / the Barometric gauge
P0107	Breakage or short circuit on the case of a chain of gauge MAR / the Barometric gauge
P0108	Short circuit on + gauge MAR chains / the Barometric gauge
P0109	Alternating error of functioning of gauge MAR / the gauge of atmospheric pressure
P0110	Infringement in a chain of the gauge of temperature of soaked up air (IAT)
P0111	Infringement of serviceability of functioning of gauge IAT
P0112	Short circuit of a chain of gauge IAT on the case
P0113	Breakage or short circuit on + gauge IAT chains
P0114	Alternating error of functioning of gauge IAT
P0115	Absence or excessively low level of a signal of the gauge of temperature of a cooler (EATS)
P0116	Excessively high level of a signal of the gauge eats / problems with efficiency of return of the engine
P0117	Short circuit of a chain of the gauge eats on the case
P0118	Breakage or short circuit on + gauge chains
P0119	Alternating error of functioning of the gauge
P0120	Malfunctions in a chain of the gauge of position throttle заслонки (TPS) / the switch And
P0121	Infringement in chain TPS / the switch And; efficiency of return of the engine Is lowered
P0122	Low entrance signal of gauge TPS / the gauge And pedal position
P0123	High entrance signal of gauge TPS / the gauge And pedal position
P0124	Alternating error of functioning of gauge TPS / the gauge-switch And
P0125	The temperature of a cooling liquid is insufficient for serviceable functioning of a feedback in a chain of management of fuel giving
P0126	The temperature of a cooling liquid is insufficient for stable functioning of a control system
P0130	Malfunction in a chain верхнепоточного a l-probe (the right number of cylinders on the V-shaped engine)
P0131	Chain low voltage верхнепоточного a warmed up l-probe (the right number of cylinders on the V-shaped engine)
P0132	High voltage верхнепоточного a warmed up l-probe (the right number of cylinders on the V-shaped engine)
P0133	The high voltage or slow reaction верхнепоточного a warmed up l-probe (the right number of cylinders on the V-shaped engine) is excessive
P0134	Absence of a signal верхнепоточного a l-probe (the right number of cylinders on the V-shaped engine)
P0135	Infringement in a heating chain верхнепоточного a l-probe (the high voltage) (the right number of cylinders on the V-shaped engine is excessive)
P0136	Infringement in a chain нижнепоточного a warmed up l-probe (the low voltage) (the right number of cylinders on the V-shaped engine is excessive)
P0137	Chain low voltage нижнепоточного a warmed up l-probe (the right number of cylinders on the V-shaped engine)
P0138	The chain high voltage нижнепоточного a warmed up l-probe (the right number of cylinders on the V-shaped engine) is excessive
P0139	Slow reaction нижнепоточного a warmed up l-probe (the right number of cylinders on the V-shaped engine)
P0140	High voltage or malfunction нижнепоточного a l-probe (the right number of cylinders on the V-shaped engine)
P0141	Infringement in a heating chain нижнепоточного a l-probe (the right number of cylinders on the V-shaped engine)
P0142	The l-probe 3 (the right number of cylinders on the V-shaped engine) is faulty
P0143	Low voltage of a l-probe 3 (the right number of cylinders on the V-shaped engine)
P0144	High voltage of a l-probe 3 (the right number of cylinders on the V-shaped engine)
P0145	The lowered reactance of a l-probe 3 (the right number of cylinders on the V-shaped engine)
P0146	Infringement of activity of functioning of a l-probe 3 (the right number of cylinders on the V-shaped engine)
P0147	The heating of a l-probe 3 (the right number of cylinders on the V-shaped engine) is faulty
P0150	Malfunction in a chain верхнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0151	Infringement of serviceability of functioning of tracing of pauperisation of a mix верхнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0152	Infringement of serviceability of tracing of enrichment of a mix верхнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0153	The slowed down reaction верхнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0154	High voltage верхнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0155	Infringement of serviceability of functioning of a heater верхнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0156	It is faulty нижнепоточный a l-probe (the left number of cylinders on the V-shaped engine)
P0157	Low voltage нижнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0158	High voltage нижнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0159	The slowed down reaction нижнепоточного a l-probe (the right number of cylinders on the V-shaped engine)
P0160	Absence of a signal нижнепоточного a l-probe (the left number of cylinders on the V-shaped engine)
P0161	Infringement of serviceability of functioning of a heater нижнепоточного a l-probe (the right number of cylinders on the V-shaped engine)
P0162	The l-probe 3 (the left number of cylinders on the V-shaped engine) is faulty
P0163	Low voltage of a l-probe 3 (the left number of cylinders on the V-shaped engine)
P0164	High voltage of a l-probe 3 (the left number of cylinders on the V-shaped engine)
P0165	The lowered reactance of a l-probe 3 (the left number of cylinders on the V-shaped engine)
P0166	Infringement of activity of functioning of a l-probe 3 (the left number of cylinders on the V-shaped engine)
P0167	The heating of a l-probe 3 (the left number of cylinders on the V-shaped engine) is faulty
P0170	Repauperization or reenrichment of an air-fuel mix (the right number of cylinders on the V-shaped engine)
P0171	Repauperization of an air-fuel mix (the right number of cylinders on the V-shaped engine)
P0172	Reenrichment of an air-fuel mix (the right number of cylinders on the V-shaped engine)
P0173	The reimpoverished or reenriched injection (the left number of cylinders on the V-shaped engine)
P0174	The reimpoverished injection (the left number of cylinders on the V-shaped engine)
P0175	The reenriched injection (the left number of cylinders on the V-shaped engine)
P0176	Malfunction in a chain of the gauge of structure of fuel
P0177	Serviceability of functioning of the gauge of structure of fuel is broken
P0178	Short circuit on weight in a chain of the gauge of structure of fuel
P0179	Short circuit on + in a chain of the gauge of structure of fuel
P0180	Malfunction in a chain of gauge A of temperature in a fuel tank
P0181	Serviceability of functioning of the gauge And fuel temperatures is broken
P0182	Short circuit on weight in a chain of the gauge And fuel temperatures
P0183	Short circuit on + in a chain of the gauge And fuel temperatures
P0184	Alternating malfunction in a chain of the gauge And fuel temperatures
P0185	Malfunction in a gauge chain In fuel temperatures
P0186	Serviceability of functioning of the gauge In fuel temperatures is broken
P0187	Short circuit on weight in a gauge chain In fuel temperatures
P0188	Short circuit on + in a gauge chain In fuel temperatures
P0189	Alternating malfunction in a gauge chain In fuel temperatures
P0190, P0191	Serviceability of functioning of the gauge of pressure of injection (on a fuel highway) is broken
P0192	Excessively low level of pressure of the gauge of pressure of injection
P0193	Excessively high level of pressure of the gauge of pressure of injection
P0194	Alternating malfunction in a chain of the gauge of pressure in a fuel highway
P0195	Malfunction in a chain of the gauge of temperature of impellent oil
P0196	Serviceability of functioning of the gauge of temperature of impellent oil is broken
P0197	Short circuit on weight in a chain of the gauge of temperature of impellent oil
P0198	Short circuit on + in a chain of the gauge of temperature of impellent oil
P0199	Alternating malfunction in a chain of the gauge of temperature of impellent oil
P0200	Malfunction in a chain of injection of fuel
P0201 -
-P0206	Malfunction in a chain of an injector of the cylinder 1 – 6 accordingly
P0214	Infringement of serviceability of functioning of an injector of cold start 2
P0215	Infringement of serviceability of functioning запорного the electromagnetic valve
P0216	Malfunction in a chain of management of distribution of injection of fuel
P0217	Engine overheat
P0218	Transmission overheat
P0219	Inadmissible excess of turns of the engine
P0220	Malfunction in chain TPS / the gauge-switch In
P0221	Infringement of serviceability of functioning TPS / the gauge-switch In
P0222	Short circuit on weight in chain TPS / the gauge-switch In
P0223	Short circuit on + in chain TPS / the gauge-switch In
P0224	Alternating malfunction TPS / the gauge-switch In
P0225	Malfunction in chain TPS / the gauge-switch
P0226	Infringement of serviceability of functioning TPS / the gauge-switch
P0227	Short circuit on weight in chain TPS / the gauge-switch
P0228	Short circuit on + in chain TPS / the gauge-switch
P0229	Alternating malfunction TPS / the gauge-switch
P0230	Malfunction in a chain of a primary contour of the fuel pump
P0231	Short circuit on weight in a chain of a secondary contour of the fuel pump
P0232	Short circuit on + in a chain of a secondary contour of the fuel pump
P0233	Alternating malfunction in a chain of a secondary contour of the fuel pump
P0261	Short circuit on weight in a chain of an injector of injection of the cylinder 1
P0262	Short circuit on + in a chain of an injector of injection of the cylinder 1
P0263	Infringement of balance of injection of an injector of the cylinder 1
P0264	Short circuit on weight in a chain of an injector of injection of the cylinder 2
P0265	Short circuit on + in a chain of an injector of injection of the cylinder 2
P0266	Infringement of balance of injection of an injector of the cylinder 2
P0267	Short circuit on weight in a chain of an injector of injection of the cylinder 3
P0268	Short circuit on + in a chain of an injector of injection of the cylinder 3
P0269	Infringement of balance of injection of an injector of the cylinder 3
P0270	Short circuit on weight in a chain of an injector of injection of the cylinder 4
P0271	Short circuit on + in a chain of an injector of injection of the cylinder 4
P0272	Infringement of balance of injection of an injector of the cylinder 4
P0273	Short circuit on weight in a chain of an injector of injection of the cylinder 5
P0274	Short circuit on + in a chain of an injector of injection of the cylinder 5
P0275	Infringement of balance of injection of an injector of the cylinder 5
P0276	Short circuit on weight in a chain of an injector of injection of the cylinder 6
P0277	Short circuit on + in a chain of an injector of injection of the cylinder 6
P0278	Infringement of balance of injection of an injector of the cylinder 6
P0300	Casual admissions of ignition in various cylinders take place
P0301 -
P0308	Ignition admissions in the cylinder 1 – 8 accordingly take place
P0320, P0321	Malfunction in an entrance contour of a chain of the control of turns of the engine of a control system of ignition distribution
P0322	Absence of a signal in an entrance contour of a chain of the control of turns of the engine of a control system of ignition distribution
P0323	Alternating malfunction in an entrance contour of a chain of the control of turns of the engine of a control system of ignition distribution
P0325	The gauge of a detonation 1 (the right number of cylinders on the V-shaped engine) is faulty
P0326	The gauge of a detonation 1 (the right number of cylinders on the V-shaped engine) is faulty
P0327	Short circuit on the case of a chain of the gauge of a detonation 1 (the right number of cylinders on the V-shaped engine)
P0328	Short circuit on + chains of the gauge of a detonation 1 (the right number of cylinders on the V-shaped engine)
P0329	Alternating malfunction in an entrance contour of the gauge of a detonation 1
P0330	The gauge of a detonation 2 (the left number of cylinders on the V-shaped engine) is faulty
P0331	The gauge of a detonation 2 (the left number of cylinders on the V-shaped engine) is faulty
P0332	Short circuit on weight of a chain of the gauge of a detonation 2 (the left number of cylinders on the V-shaped engine)
P0333	Short circuit on + in a chain of the gauge of a detonation 2 (the left number of cylinders on the V-shaped engine)
P0334	Alternating malfunction in an entrance contour of the gauge of a detonation 2 (the left number of cylinders on the V-shaped engine)
P0335	Signal of turns of the engine / Malfunction in a chain of the gauge And position of cranked shaft СКР
P0336	The gauge And positions of cranked shaft СКР
P0337	Short circuit on the case in a chain of gauge SKR And
P0338	Short circuit on + in a chain of gauge SKR And
P0339	Alternating malfunction in a chain of gauge SKR And
P0340	Malfunction in a chain of the gauge of position of camshaft СМР
P0341	Infringement of serviceability of functioning of gauge SMR
P0342	Short circuit on weight in gauge SMR chain
P0343	Short circuit on + in gauge SMR chain
P0344	Alternating malfunction in gauge SMR chain
P0350	Malfunction in primary / a secondary contour of the coil of ignition
P0351 -
-P0362	Malfunction in primary / a secondary contour of the coil of ignition And – L accordingly
P0370	Malfunction in a chain of a basic signal of the high permission And management of installation of a corner of an advancing of ignition
P0371	Malfunction in a chain of a basic signal of the high permission And management of installation of a corner of an advancing of ignition (excessive quantity of impulses)
P0372	Malfunction in a chain of a basic signal of the high permission And management of installation of a corner of an advancing of ignition (insufficient quantity of impulses)
P0373	Alternating malfunction in a chain of a basic signal of the high permission And management of installation of a corner of an advancing of ignition (arrhythmy of impulses)
P0374	Malfunction in a chain of a basic signal of the high permission And management of installation of a corner of an advancing of ignition (absence of impulses)
P0375	Malfunction in a chain of a basic signal of the high permission In managements of installation of a corner of an advancing of ignition
P0376	Malfunction in a chain of a basic signal of the high permission In managements of installation of a corner of an advancing of ignition (excessive quantity of impulses)
P0377	Malfunction in a chain of a basic signal of the high permission In managements of installation of a corner of an advancing of ignition (insufficient quantity of impulses)
P0378	Alternating malfunction in a chain of a basic signal of the high permission In managements of installation of a corner of an advancing of ignition (arrhythmy of impulses)
P0379	Malfunction in a chain of a basic signal of the high permission In managements of installation of a corner of an advancing of ignition (absence of impulses)
P0385	Malfunction in gauge SKR chain In
P0386	Infringement of serviceability of functioning of gauge SKR In
P0387	Short circuit on weight in gauge SKR chain In
P0388	Short circuit on + in gauge SKR chain In
P0389	Alternating malfunction in gauge SKR chain In
P0400	Excessiveness or insufficiency of intensity рециркуляции the fulfilled gases (EGR)
P0401	Easing of stream EGR is revealed
P0402	Excessive strengthening of stream EGR Malfunction in a gauge chain противодавления EGR is revealed
P0403	Malfunction in valve EGR chain
P0404	Infringement of serviceability of functioning of chain EGR
P0405	Short circuit on weight in a chain of the gauge And EGR
P0406	Short circuit on + in a chain of the gauge And EGR
P0407	Short circuit on weight in a gauge chain In EGR
P0408	Short circuit on + in a gauge chain In EGR
P0410	Malfunction in system подмешивания additional air
P0411	Wrong definition of a stream by system подмешивания additional air
P0412	Malfunction in a valve And system chain подмешивания additional air
P0413	Breakage or short circuit on + valve And system chains подмешивания additional air
P0414	Short circuit on the case of a chain of the valve And system подмешивания additional air
P0415	Malfunction in a valve-switch chain In systems подмешивания additional air
P0416	Breakage in a valve-switch chain In systems подмешивания additional air
P0417	Short circuit in a valve-switch chain In systems подмешивания additional air
P0418	Infringement of serviceability of functioning of the relay And system подмешивания additional air
P0419	Infringement of serviceability of functioning of the relay In systems подмешивания additional air
P0420 -
-P0423	Infringement of serviceability of functioning каталитического the converter (the right number of cylinders on the V-shaped engine)
P0424	Excessive decrease in temperature каталитического the converter (the right number of cylinders on the V-shaped engine)
P0430 -
-P0433	Efficiency of functioning каталитического the converter (the left number of cylinders on the V-shaped engine) is excessively lowered
P0434	Excessive decrease in temperature каталитического the converter (the left number of cylinders on the V-shaped engine)
P0440	Leaks in system of catching of steams of fuel EVAP
P0441	It is faulty VSV systems EVAP
P0442	Insignificant leak in system EVAP is revealed
P0443 -
-R0446	Malfunction in a chain of the valve of management of a purge of coal adsorber EVAP
P0447	Breakage in a chain of management of system EVAP ventilation
P0448	Short circuit in a chain of management of system EVAP ventilation
P0449	Malfunction in a chain of the electromagnetic valve / the valve of ventilation of system EVAP
P0450	Infringement in a chain of the gauge of pressure of steams in system EVAP petrol tank
P0451	Infringement of serviceability of functioning of system EVAP
P0452	Low entrance signal of the gauge of pressure in a fuel tank (system EVAP)
P0453	High entrance signal of the gauge of pressure in a fuel tank (system EVAP)
P0454	Alternating malfunction of the gauge of pressure of system EVAP
P0455	Considerable leak in system EVAP is revealed
P0460	Malfunction in a chain of the gauge of level of fuel
P0461	Infringement of serviceability of functioning of the gauge of level of fuel
P0462	Short circuit on weight in a chain of the gauge of level of fuel
P0463	Short circuit on + in a chain of the gauge of level of fuel
P0464	Alternating malfunction in a chain of the gauge of level of fuel
P0465	Malfunction in a chain of the gauge of a stream of a purge
P0466	Infringement of serviceability of functioning of the gauge of a stream of a purge
P0467	Short circuit on weight in a chain of the gauge of a stream of a purge
P0468	Short circuit on + in a chain of the gauge of a stream of a purge
P0469	Alternating malfunction of the gauge of a stream of a purge
P0470	Malfunction in a chain of the gauge of pressure of the fulfilled gases
P0471	Infringement of serviceability of functioning of the gauge of pressure of the fulfilled gases
P0472	Short circuit on weight in a chain of the gauge of pressure of the fulfilled gases
P0473	Short circuit on + in a chain of the gauge of pressure of the fulfilled gases
P0474	Alternating malfunction in a chain of the gauge of pressure of the fulfilled gases
P0475	Malfunction in a chain of the operating valve of pressure of the fulfilled gases
P0476	Infringement of serviceability of functioning of the operating valve of pressure of the fulfilled gases
P0477	Short circuit on weight in a chain of the operating valve of pressure of the fulfilled gases
P0478	Short circuit on + in a chain of the operating valve of pressure of the fulfilled gases
P0479	Alternating malfunction in a chain of the operating valve of pressure of the fulfilled gases
P0480	Malfunction in a chain of management of the fan of 1 system of cooling
P0481	Malfunction in a chain of management of the fan of 2 systems of cooling
P0482	Malfunction in a chain of management of the fan of 3 systems of cooling
P0483	Refusal at check of rationality of functioning of the fan of system of cooling
P0484	Overload on a current in a chain of the fan of system of cooling
P0485	Malfunction in a feed circuit / grounding of the fan of system of cooling
P0500, P0501	Malfunction in a chain of the gauge of speed of car VSS
P0502	Absence of a signal or short circuit on gauge VSS case
P0503	Instability / rhythm infringement / signal overestimate in work VSS
P0505	Malfunction in a chain of gauge IAC of stabilisation of turns of idling
P0506	Unexpected understating of frequency of rotation of the engine at operation of system of stabilisation of turns of idling
P0507	Unexpected overestimate of frequency of rotation of the engine at operation of system of stabilisation of turns of idling
P0510	Malfunction in a chain д/в the closed position throttle заслонки TPS
P0520	Malfunction in a gauge chain / the gauge-switch of pressure of impellent oil
P0521	Infringement of serviceability of functioning of the gauge / the gauge-switch of pressure of impellent oil
P0522	Short circuit on weight in a gauge chain / the gauge-switch of pressure of impellent oil
P0523	Short circuit on + in a gauge chain / the gauge-switch of pressure of impellent oil
P0530	Infringement of a chain of the gauge of pressure of a coolant of system K/V
P0531	Infringement of serviceability of functioning of the gauge of pressure of a coolant of system K/V
P0532	Short circuit on weight in a chain of the gauge of pressure of a coolant of system K/V
P0533	Short circuit on + in a chain of the gauge of pressure of a coolant of system K/V
P0534	Discharge (coolant loss) in охладительном system K/V contour
P0535	Absence or instability of a signal of turns of the engine - ignitions
P0550	Malfunction in a chain of the gauge of pressure of system PAS (the wheel hydraulic booster)
P0551	Infringement of serviceability of functioning of the gauge of pressure of system PAS (the wheel hydraulic booster)
P0552	Short circuit on weight in a chain of the gauge of pressure of system PAS (the wheel hydraulic booster)
P0553	Short circuit on + in a chain of the gauge of pressure of system PAS (the wheel hydraulic booster)
P0554	Alternating malfunction in a chain of the gauge of pressure of system PAS (the wheel hydraulic booster)
P0560	Malfunction in system of onboard power supplies
P0561	Infringement of stability of pressure of onboard power supplies
P0562	Understating of pressure of onboard power supplies
P0563	Overestimate of pressure of onboard power supplies
P0565	Infringement at development of a signal of inclusion темпостата
P0566	Infringement at development of a signal of deenergizing темпостата
P0567	Infringement at development of a signal of return (RESUME) темпостата
P0568	Infringement at development of a signal of installation (SET) темпостата
P0569	Infringement at development of a signal of movement накатом (CAST) темпостата
P0570	Infringement at development of a signal of an acceleration (ACCEL) темпостата
P0571	Malfunction in a gauge-switch And braking chain темпостата
P0572	Short circuit on weight in a gauge-switch And braking chain темпостата
P0573	Short circuit on + in a gauge-switch And braking chain темпостата
P0574 -
-P0580	Reserve zone of a control system in the speed (темпостата)
P0600	Malfunction of a serial port of the block of management АТ
P0601	Error at calculation of the control sum of memory of the module of management
P0602	Error of programming of the module of management
P0603	Error of regeneration of memory (КАМ) the management module
P0604	RAM error (RAM) the management module
P0605	ROM error (ROM) the management module
P0606	Processor RSM refusal
P0608	Infringement at development of a target signal And the module of management VSS
P0609	Infringement at development of a target signal In the module of management VSS
P0620	Malfunction in a chain of management of the generator
P0621	Malfunction in a chain of management L of a control lamp of the generator
P0622	Malfunction in field chain F of management of the generator
P0650	Malfunction in a chain of a control lamp of refusals (MIL)
P0654	Malfunction in a chain of a target signal of turns of the engine
P0655	Malfunction in a chain of a target signal of a control lamp of an overheat of the engine
P0656	Malfunction in a chain of a target signal of level of fuel
P0700	Infringement of serviceability of functioning of a control system by transmission
P0701	Malfunction in a chain of a target signal of turns of engine AT
P0702	Electric malfunction in a chain of a control system of transmission
P0703	Malfunction in a gauge-switch chain In braking / the rotation converter
P0704	Malfunction in an entrance contour of a chain of the gauge-switch of coupling
P0705	Malfunction in a chain of the gauge-switch of position of transmission
P0706	Malfunction in a chain of the gauge-switch of position of transmission
P0707	Short circuit on weight in a chain of the gauge-switch of positions of transmission
P0708	Short circuit on + in a chain of the gauge-switch of positions of transmission
P0709	Alternating malfunction in a chain of the gauge-switch of positions of transmission
P0710	Malfunction in a chain of the gauge of temperature ATF
P0711	Malfunction in a chain of the gauge of temperature ATF
P0712	Short circuit on weight in a chain of the gauge of temperature ATF
P0713	Short circuit on + in a chain of the gauge of temperature ATF
P0714	Alternating malfunction in a chain of the gauge of temperature ATF
P0715	Malfunction in an entrance contour of a chain of the gauge of turns of the turbine
P0716	Malfunction in an entrance contour of a chain of the gauge of turns of the turbine
P0717	Absence of a signal in an entrance contour of a chain of the gauge of turns of the turbine
P0718	Alternating malfunction in an entrance contour of a chain of the gauge of turns of the turbine
P0719	Short circuit on weight in a gauge-switch chain In braking / the rotation converter
P0720	Malfunction in a chain of the gauge of turns
P0721	Infringement of serviceability of functioning of the gauge of turns
P0722	Absence of a target signal of the gauge of turns
P0723	Alternating malfunction of the gauge of turns
P0724	Short circuit on + in a gauge-switch chain In braking / the rotation converter
P0725	Failures in giving of a signal of turns of the engine
P0726	Malfunction in an entrance contour of a chain of registration of turns of the engine
P0727	Absence of an entrance signal in a chain of registration of turns of the engine
P0728	Alternating malfunction in an entrance contour of a chain of registration of turns of the engine
P0730	Wrong choice of transfer АТ
P0731 -
-P0735	Failures in giving of a signal of inclusion 1 - 5th transfers accordingly
P0736	Failures in giving of a signal of inclusion of a reverse gear
P0740	Malfunction in a chain of an electromagnet of valve TSS AT
P0741	Залипание in the opened condition of coupling of transformation of rotation
P0742	Залипание in the closed condition of coupling of the converter of rotation
P0743	Electric refusal in a chain of coupling of the converter of rotation
P0744	Alternating malfunction in a chain of coupling of the converter of rotation АТ
P0745	Malfunction in a chain of the electromagnetic valve of pressure in a path
P0746	Залипание in the opened condition of the electromagnetic valve of management of pressure
P0747	Залипание in the closed condition of the electromagnetic valve of management of pressure
P0748	Electric malfunction in a chain of the electromagnetic valve of management of pressure
P0749	Alternating malfunction of the electromagnetic valve of management of pressure
P0750	Infringement of serviceability of functioning of the electromagnetic valve of switching And
P0751	Залипание in the opened condition of the electromagnetic valve of switching And
P0752	Залипание in the closed condition of the electromagnetic valve of switching And
P0753	Electric malfunction in a chain of the electromagnetic valve of switching And
P0754	Alternating malfunction of the electromagnetic valve of switching And
P0755	Infringement of serviceability of functioning of the electromagnetic valve of switching In
P0756	Залипание in the opened condition of the electromagnetic valve of switching In
P0757	Залипание in the closed condition of the electromagnetic valve of switching In
P0758	Electric malfunction in a chain of the electromagnetic valve of switching In
P0759	Alternating malfunction of the electromagnetic valve of switching In
P0760	Infringement of serviceability of functioning of the electromagnetic valve of switching
P0761	Залипание in the opened condition of the electromagnetic valve of switching
P0762	Залипание in the closed condition of the electromagnetic valve of switching
P0763	Electric malfunction in a chain of the electromagnetic valve of switching
P0764	Alternating malfunction of the electromagnetic valve of switching
P0765	Infringement of serviceability of functioning of the electromagnetic valve of switching D
P0766	Залипание in the opened condition of the electromagnetic valve of switching D
P0767	Залипание in the closed condition of the electromagnetic valve of switching D
P0768	Electric malfunction in a chain of the electromagnetic valve of switching D
P0769	Alternating malfunction of the electromagnetic valve of switching D
P0770	Infringement of serviceability of functioning of the electromagnetic valve of switching
P0771	Залипание in the opened condition of the electromagnetic valve of switching
P0772	Залипание in the closed condition of the electromagnetic valve of switching
P0773	Electric malfunction in a chain of the electromagnetic valve of switching
P0774	Alternating malfunction of the electromagnetic valve of switching
P0780	Infringement at a gear change
P0781	Infringement at a gear change 1 - 2
P0782	Infringement at a gear change 2 - 3
P0783	Infringement at a gear change 3 - 4
P0784	Infringement at a gear change 4 - 5
P0785	Malfunction of the electromagnetic valve of switching / distributions
P0786	Malfunction of the electromagnetic valve of switching / distributions
P0787	Short circuit on weight in a chain of the electromagnetic valve of switching / distributions
P0788	Short circuit on + in a chain of the electromagnetic valve of switching / distributions
P0789	Alternating malfunction of the electromagnetic valve switching
P0790	Malfunction in a chain of the gauge-switch of modes АТ
P0801	Malfunction in a management chain ингибитора a backspacing
P0803	Malfunction in a chain of increase of transfers 1 - 4 (admissions at switching)
P0804	Malfunction in a chain of a control lamp of admissions at increase of transfer 1 - 4
P1100	Malfunction in a chain of the gauge of position of the electromotor of management of an induction
P1101	Malfunction in a chain of the electromagnetic valve of management of depth of depression антипробуксовочной systems
P1102	Malfunction in a chain of the electromagnetic valve of management of ventilation антипробуксовочной systems
P1105	Malfunction in a chain of the electromagnetic valve of pressure of fuel
P1294	Demanded turns of idling are not reached
P1295	On TPS pressure 5 does not stand out In
P1296	On gauge MAP pressure 5 does not stand out In
P1297	There are no changes in pressure indications in the pipeline in modes of start and working operation of the engine
P1300	Malfunction in a chain of adjustment of a corner of an advancing of ignition
P1390	Проскакивание газораспределительного a belt on one tooth or more
P1391	Astable refusal in development of signals of gauge CKP/CMP
P1400	Malfunction in a chain of the differential gauge of pressure in the pipeline
P1443	Malfunction in a chain of the valve of 2 managements of a purge of coal adsorber EVAP
P1486	Passableness of a hose of monitoring of leaks EVAP is broken
P1487	Malfunction in a chain of the relay of management of a high-speed mode of the fan of system of cooling
P1490	Malfunction in a chain of the relay of management низкоскоростного a mode of the fan of system of cooling
P1492	Pressure of the gauge of temperature of the battery is overestimated
P1494	The gauge-switch of ventilation EVAP / mechanical defect of system is faulty
P1495	Malfunction in a chain of the electromagnetic valve of ventilation EVAP
P1496	It is underestimated target 5-voltnoe pressure
P1500	Malfunction of a contour of plug FR of the generator
P1600	Malfunction of a contour of consecutive connection PCM-TCM
P1696	Incorrect record EEPROM in PCM
P1715	Messages CCD from TCM do not arrive
Р1720	Malfunction in an entrance chain of the gauge of speed of the car
P1750	Malfunction in a chain of pulse generator TCM
Р1751	Malfunction of the relay of management АТ
P1791	Malfunction in a chain of management of electromagnet TCC of operating pressure of switching
Р1795	Malfunction in an entrance chain of position throttle заслонки
P1899	Incorrect level of signal ECT PCM to TCM
P1989	Malfunction of the relay of management of the condenser of a high-speed mode of the fan of system of cooling

Codes Mitsubishi which is read out by means of the voltmeter

Codes of malfunctions of system of safety SRS

The structure of the module of management SRS includes the self-diagnostics block. Reading written down in memory of the module of codes of malfunctions is made by connection of the special scanner to diagnostic socket DLC.

Clearing of memory of the module is made by means of the same scanner.

The list of codes of the most typical refusals SRS is more low resulted.

№ a code	Source and possible cause of a failure
11	Short circuit on weight in a chain of forward gauges of the directed overloads;
	Malfunction of the module of management SRS
12	Breakage or short circuit on + in a chain of forward gauges of the directed overloads;
	Malfunction of the module of management SRS
13	Breakage or short circuit on + in a chain of forward gauges of the directed overloads;
	Malfunction of the module of management SRS
14	Malfunction of the gauge of the directed overloads in the module of management SRS
15	Short circuit in a chain of the control gauge of face-to-face overloads in module SRS
16	Breakage in a chain of the control gauge of face-to-face overloads in module SRS
17	Malfunction of the control gauge of lateral overloads in module SRS
21	Short circuit in a chain of the module of a driver's pillow of safety (including a drum-type cable socket)
22	Breakage in a chain of the module of a driver's pillow of safety (including a drum-type cable socket)
24	Short circuit in a chain of the module of a passenger pillow of safety
25	Breakage in a chain of the module of a passenger pillow of safety
26	Short circuit in a chain emergency натяжителя a driver's seat belt
27	Breakage in a chain emergency натяжителя a driver's seat belt
28	Short circuit in a chain emergency натяжителя a passenger seat belt
29	Breakage in a chain emergency натяжителя a passenger seat belt
31	Malfunction of the condenser of the gauge of face-to-face overloads in the module of management SRS
32	Malfunction of the condenser of the gauge of face-to-face overloads in the module of management SRS
33	Signal проворачивания the module of management SRS;
	Malfunction in electroconducting
34	Infringement of quality of contact connections in a chain of the module of management SRS
35	Record of a signal of emergency collision in memory of module SRS
41	The low voltage of a food of module SRS, - safety lock failure, electroconducting damage is excessive;
	The module of management SRS is faulty
42	The low voltage of a food of module SRS, - safety lock failure, electroconducting damage is excessive;
	The module of management SRS is faulty
43	Refusal of control lamp SRS, - electroconducting breakage (including a lamp incandescent filament);
	Malfunction of the module of management SRS;
	Malfunction of an instrument guard
44	Refusal of control lamp SRS, - malfunction of the module of management SRS
45	Malfunction of the module of management SRS, - EEPROM
46	Malfunction in a chain of collisions of the module of management SRS
47	Malfunction in a chain of the activator of a driver's pillow of safety, - short circuit in a chain of the module of management SRS
48	Malfunction in a chain of the activator of a driver's pillow of safety, - breakage in a chain of the module of management
51	Malfunction in a chain of the activator of a driver's pillow of safety, - short circuit in a chain of the module of management SRS
52	Malfunction in a chain of the activator of a driver's pillow of safety, - breakage in a chain of the module of management
54	Malfunction in a chain of the activator of a passenger pillow of safety, - short circuit in a chain of the module of management SRS
55	Malfunction in a chain of the activator of a passenger pillow of safety, - breakage in a chain of the module of management
56	Malfunction in a chain of the activator emergency натяжителя a driver's seat belt, - short circuit in a chain of the module of management SRS
57	Malfunction in a chain of the activator emergency натяжителя a driver's seat belt, - breakage in a chain of the module of management SRS
58	Malfunction in a chain of the activator emergency натяжителя a passenger seat belt, - short circuit in a chain of the module of management SRS
59	Malfunction in a chain of the activator emergency натяжителя a passenger seat belt, - breakage in a chain of the module of management SRS
61	Short circuit on + in a chain of a driver's pillow of safety, - malfunction of electroconducting or the module of management SRS
62	Short circuit on weight in a chain of a driver's pillow of safety, - malfunction of electroconducting or the module of management SRS
64	Short circuit on + in a chain of a passenger pillow of safety, - malfunction of electroconducting or the module of management SRS
65	Short circuit on weight in a chain of a passenger pillow of safety, - malfunction of electroconducting or the module of management SRS
66	Short circuit on + in a chain натяжителя a driver's seat belt, - malfunction of electroconducting or the module of management SRS
67	Short circuit on weight in a chain натяжителя a driver's seat belt, - malfunction of electroconducting or the module of management SRS
68	Short circuit on + in a chain натяжителя a passenger seat belt, - malfunction of electroconducting or the module of management SRS
69	Short circuit on weight in a chain натяжителя a passenger seat belt, - malfunction of electroconducting or the module of management SRS
71	Short circuit in a chain of the left lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
71	Short circuit in a chain of the right lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
72	Breakage in a chain of the left lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
72	Breakage in a chain of the right lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
73	Refusal of the activator of the left lateral pillow of safety (except models Galant), - short circuit in a chain of the module of management SRS
73	Refusal of the activator of the right lateral pillow of safety (model Galant), - short circuit in a chain of the module of management SRS
74	Refusal of the activator of the left lateral pillow of safety (except models Galant), - breakage in a chain of the module of management SRS
74	Refusal of the activator of the right lateral pillow of safety (model Galant), - breakage in a chain of the module of management SRS
75	Short circuit on + in a chain of the left lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
75	Short circuit on + in a chain of the right lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
76	Short circuit on weight in a chain of the left lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
76	Short circuit on weight in a chain of the right lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
79	Infringement of communications of the gauge of the directed overloads of the left lateral pillow of safety, - malfunction of electroconducting or the module of management SRS
81	Short circuit in a chain of the right lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
81	Short circuit in a chain of the left lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
82	Breakage in a chain of the right lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
82	Breakage in a chain of the left lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
83	Malfunction of the activator of the right lateral pillow of safety (except models Galant), - short circuit in a chain of the module of management SRS
83	Malfunction of the activator of the left lateral pillow of safety (model Galant), - short circuit in a chain of the module of management SRS
84	Malfunction of the activator of the right lateral pillow of safety (except models Galant), - breakage in a chain of the module of management SRS
84	Malfunction of the activator of the left lateral pillow of safety (model Galant), - breakage in a chain of the module of management SRS
85	Short circuit on + in a chain of the right lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
85	Short circuit on + in a chain of the left lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
86	Short circuit on weight in a chain of the right lateral pillow of safety (except models Galant), - malfunction of electroconducting or the module of management SRS
86	Short circuit on weight in a chain of the left lateral pillow of safety (model Galant), - malfunction of electroconducting or the module of management SRS
89	Infringement of communications of the gauge of the directed overloads of the right lateral pillow of safety, - malfunction of electroconducting or the module of management SRS
91	The low voltage of a food of the gauge of the directed overloads of the left lateral pillow of safety, - malfunction of the gauge or the module of management SRS is excessive
92	Refusal of the gauge of the directed overloads of the left lateral pillow of safety
93	Wrong communications of the gauge of the directed overloads of the left lateral pillow of safety, - malfunction of electroconducting or the module of management SRS
94	The low voltage of a food of the gauge of the directed overloads of the right lateral pillow of safety, - malfunction of the gauge or the module of management SRS is excessive
95	Refusal of the gauge of the directed overloads of the right lateral pillow of safety
96	Wrong communications of the gauge of the directed overloads of the right lateral pillow of safety, - malfunction of electroconducting or the management module