Mitsubishi Galant

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Disconnect from the lever приводной selector AT cable.

3. Turn out two fixing screws and remove the gauge-switch.

1. Establish the gauge-switch on the regular place. Screw fixing bolts, however do not tighten them before end of adjustment of the gauge-switch.
2. Connect to the gauge-switch electroconducting and make its adjustment (see more low).
3. Connect a negative wire to the battery.
4. Make sure, that engine start is obviously possible only in positions “Р” and “N” to transmission. Also check up serviceability of operation of fires of a backing while translating the selector lever in position “R”.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Cock a lay brake and prop up car wheels противооткатными boots.
3. Find established from above on crankcase transmissions the gauge-switch of the permission of start.
4. Ослабьте an adjusting nut of a cable of a drive of switching on crankcase transmissions. In car salon translate the selector lever in position “N”.
5. A manual control lever transmission switching also translate in position “N”.
6. Release screws of fastening of the gauge-switch and develop last so that the 5-millimetric aperture in its case was combined with a reciprocal aperture (also 5-millimitrovym) in the manual lever of switching.
7. Tighten bolts of fastening of the gauge-switch with demanded effort (10 ч 12H•м).
8. Having delayed приводной a cable around an adjusting nut, completely choose its weak point, then tighten a nut with effort 12 H•м.
9. Make sure, that the gauge-switch lever at switching of modes АТ from salon moves to corresponding position.
10. Connect a negative wire to the battery.
11. Make sure, that engine start is possible only in positions “Р” and “N” transmissions. Also check up serviceability of operation of fires of a backing while translating the selector lever in position “R”.

1. The Gauge-switch of the permission of start on the given models also is from above on crankcase transmissions.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Disconnect from the lever приводной selector AT cable.
4. Give a fastening nut приводного a cable of management of transmission switching to the manual lever of transmission. Take a cable aside.
5. Translate the manual lever in position “N”, then give a nut on the lever.
6. Disconnect electroconducting from the gauge-switch of the permission of start.
7. Turn out fixing bolts and remove the gauge-switch.

1. Establish the gauge-switch on the regular place. Screw, but do not tighten while fixing bolts.
2. Connect to the gauge-switch the manual lever and fix its nut, - track, that the lever remained in position “N”.
3. Execute gauge-switch adjustment (see more low), then definitively tighten bolts of fastening of the gauge-switch with demanded effort (11 H•м).
4. Connect to the gauge-switch electroconducting.
5. Connect a cable of a drive of switching, choose its weak point, check up freedom of moving of the lever and tighten a nut of fastening of a cable.
6. Connect a negative wire to the battery.
7. Make sure, that engine start is obviously possible only in positions “Р” and “N” to transmission. Also check up serviceability of operation of fires of a backing while translating the selector lever in position “R”.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Cock a lay brake and prop up car wheels противооткатными boots.
3. Find established from above on crankcase transmissions the gauge-switch of the permission of start.
4. Ослабьте an adjusting nut of a cable of a drive of switching on crankcase transmissions. In car salon translate the selector lever in position “N”.
5. A manual control lever transmission switching also translate in position “N”.
6. Release screws of fastening of the gauge-switch and develop last so that the 5-millimetric aperture in its case was combined with a reciprocal aperture (also 5-millimitrovym) in the manual lever of switching, - pass in apertures a drill of suitable diameter and tighten bolts of fastening of the gauge-switch with demanded effort (11 H•м).
7. Having delayed приводной a cable around an adjusting nut, completely choose its weak point, then tighten a nut with effort 12 H•м.
8. Check up freedom of a course of the manual lever.
9. Connect a negative wire to the battery.
10. Make sure, that engine start is possible only in positions “Р” and “N” transmissions. Also check up serviceability of operation of fires of a backing while translating the selector lever in position “R”.

2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Turn out two fixing bolts and remove the gauge-switch.

1. Establish the gauge-switch on the regular place. Screw, but do not tighten while fixing bolts.
2. Execute gauge-switch adjustment (see more low), then definitively tighten bolts of fastening of the gauge-switch with demanded effort (10 ч 12 H•м).
3. Connect a cable of a drive of switching.
4. Connect a negative wire to the battery.
5. Connect to the gauge-switch electroconducting.
6. Make sure, that engine start is possible only in positions “Р” and “N” transmissions. Also check up serviceability of operation of fires of a backing while translating the selector lever in position “R”.

1. Adjustment, as well as earlier, is made by combination of 5-millimetric apertures in the case of the gauge-switch and a body of the manual lever of a drive of switching.
2. In summary make sure, that engine start is possible only in positions “Р” and “N” transmissions. Also check up serviceability of operation of fires of a backing while translating the selector lever in position “R”.